High Reliability Pneumatic Vertical Shock/Bump Test Machine
KRD11 series pneumatic vertical shock/bump test system is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.
l Pneumatic drive, simple structure and high reliability
l Pollution free, without hydraulic leak risk and keep the environment clean.
l Pneumatic drive greatly improves the shock test efficiency, maximum shock rate up to 120 times / min.
l It can easily realize large pulse width and small overload test.
l With a fast shock rate comparing to motor or hydraulic driven collision table, it has higher reliability and better collision waveform.
l The speed and rate of shock can be easily controlled by adjusting the gas pressure.
l KRD90 series shock control and measurement system can perform manual shock, continuous shock, single shock, and interval shock.
l Built-in brake mechanism ensures the safety of operation in any situation.
Technical Specifications
Model Parameters |
KRD 11-5 |
KRD 11-15 |
KRD 11-25 |
KRD 11-50 |
KRD 11-100 |
KRD 11-200 |
KRD 11-400 |
KRD 11-600 |
KRD 11-800 |
KRD 11-1000 |
KRD 11-2000 |
||
Rated Load (kg) |
5 |
15 |
25 |
50 |
100 |
200 |
400 |
600 |
800 |
1000 |
2000 |
||
Table Size (mm) |
150×150 |
200×200 |
300×300 |
500×500 |
600×600 |
800×600 |
800×800 |
1000×800 |
1000×1000 |
1200×1200 |
1500×1200 |
||
Peak Acc. (g) |
Half-Sine |
5-2.5k |
5-2k |
5-1500 |
10-750 |
10-600 |
10-450 |
10-400 |
10-300 |
10~300 |
10~250 |
10~150 |
|
Post-Peak Sawtooth |
10-200 |
10-100 |
10-50 |
||||||||||
Trapezoid |
15-200 |
15-100 |
15-60 |
15-50 |
|||||||||
Pulse Duration (ms) |
Half-Sine |
|
1~40 |
|
2~60 |
|
3~60 |
|
4~60 |
|
6~60 |
||
Post-Peak Sawtooth |
3~18 |
6~18 |
|||||||||||
Trapezoid |
3~18 |
6~18 |
|||||||||||
Bump Waveform |
Half sine wave |
||||||||||||
Bump Peak Acceleration (g) |
4~150 |
5~100 |
|||||||||||
Bump Pulse Duration (ms) |
2~30 |
3~30 |
|||||||||||
Overall Dimension (mm) |
1000×1000 ×2100 |
1200×1000 ×2200 |
1400×1200 ×2300 |
1600×1400 ×2300 |
1700×1500 ×2300 |
1700×1500 ×2300 |
1900×1500 ×2450 |
1900×1500 ×2450 |
2000×1500 ×2450 |
1900×1800 ×2550 |
2200×1800 ×2550 |
||
Weight (kg) |
700 |
800 |
1000 |
1800 |
2500 |
2800 |
3800 |
4000 |
4800 |
5200 |
6000 |
||
Bump Rate (Times/Min) |
10~120 |
||||||||||||
Installation Condition |
Environment |
Temperature range 0 ~ 40℃; Humidity ≤ 80%, non-condense |
|||||||||||
Power |
AC220V±10%, 50Hz |
||||||||||||
Air source |
≤0.8MPa |
||||||||||||
Floor |
Foundation-free, the cement floor shall be leveled and the working distance of 800 ~ 1000mm shall be reserved around the equipment |
||||||||||||
Standards |
MIL-STD-810F IEC68-2-27 |
Send product request
Other supplier products
KRD70 Hydraulic Vibration Shaker | KRD70 series hydraulic vibration shaker converts the energy of high-pressure liquid into the power of the reciprocating motion of the cylinder thro... | |
KRD32 Non-standard Constant Acceleration Tester | KRD32 series non-standard constant acceleration testing machine is test equipment for military products to simulate dynamic centrifugal motion, dua... | |
Zero Distance Drop Test Machine | KRD40 series drop tester, mainly simulates the resistance to drop and impact of large and heavy packaging products. Its strong power system and uni... | |
KRD11 Pneumatic Vertical Shock/Bump Test System | KRD11 series pneumatic vertical shock/bump test system is featured with advanced design, high degree of automation and reliability, simple operatio... | |
KRD10 Hydraulic Vertical Shock Test System | KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to eva... |
Same products
BS EN 12600 Two Tyres Impactor | Seller: Qinhuangdao Yuanchen Technology Equipment Co., Ltd. | Reference Standard: BS EN 12600:2002Glass in building – Pendulum test – Impact test m... | |
Hast Pct High-Low Temperature Test Chamber with Pressure | Seller: AI SI LI (China) Test Equipment Co., Ltd. | HAST PCT High-low Temperature Test Chamber With Pressureis widely applied to the testing of seali... | |
Programmable Hast Accelerated Aging Tester for Industry | Seller: AI SI LI (China) Test Equipment Co., Ltd. | HAST (Highly Accelerated Stress Test) is a type of test that is used to evaluate the reliability ... | |
CE Certificated Lab Equipment Transport Vibration Tester for Un38.3 Standard | Seller: AI SI LI (China) Test Equipment Co., Ltd. | CE Certificated Lab Equipment Transport Vibration Tester for UN38.3 Standardis applied to test th... | |
Package Large Scale Simulation Transportation Vibration Tester | Seller: AI SI LI (China) Test Equipment Co., Ltd. | This machine is used to simulation testing damage between transport for various package stuff, PC... |