Blankets Flammability Tester
Introduction
The test instrument is used to detect the flame resistance of the blanket fabric and the flame spread performance of the fabric surface. The test method is to burn the surface of the specimen with a standardized flame for a specified period of time. Thus, the burning, damage degree and color change of standard test paper are observed and then assess the test fabric grade.
Structure
Flowmeter :Adjust the gas flow size.
Fire tube : The gas is first connected to the flow meter through the hose, and then through the rear hose of the box into the flame pipe
Windscreen: the upper part of the windshield is provided with glass
The experiment was carried out in a ventilated kitchen. The round hole on the top of the box and the gap on the windshield make the gas convection.
Control panel :Power- power switch ;Start：Start internal motor operation. When the flame tube moves to the test position (the vertical distance from the sample center is 8mm, the horizontal distance is 3.2mm), the internal timing switch is touched;
Reset :Timer reset /Fire tube reset.
Sample clamp and specimen holder :The sample frame substrate is provided with a knob which can adjust the left and right movement, and the sample frame substrate is moved and fixed by loosening and tightening the knob.
Timer :Display settings and actual ignition time.After the time is cleared, the fire tube can complete the required movement. Or the fire tube can not return to the original position after moving forward.
Standards
ASTM D4151 Standard Test Method for Flammability of Blankets
Operation
After the sample is ready and the instrument is commissioned, place the assembled sample clamp on the specimen holder.
Open the gas valve and supply the gas to the fire pipe. Use the electronic igniter to fire the burner
Press the start button on the control panel. The fire tube moves forward and moved to the test position under the action of the mechanical transmission. Then, Start the ignition of the sample and test paper on the sample holder
At the same time to start the ignition timing system, the control panel display and record the ignition time. After a second, the fire tube moving backwards, the timer stop time. The experiment is end.
Finally remove the sample and test paper for rating.
Features
Stainless steel case with transparent viewing window
18 Needle flame, flame length adjustable
Ignition time can be set freely
Provide bristles and sample clamps
Provide standard stainless steel sample holder
Technical Parameters
| Items | Parameter |
|---|---|
| Needle flame number | 1 |
| Timer accuracy | 0.01s |
| Dimensions | 370×218×510mm（W×H×D） |
| Power supply | 220V, 50HZ,1.0A |
Send product request
Other supplier products
 |
Thermal Insulation Rock Wool Thermal Load Tester | Introduction： This equipment determines the temperature at which rock wool insulation shrinks under a specified load when heated at a controlled r... |
 |
Burning Manikin System | The burning manikin system is used to test the overall thermal protection performance of protective clothing.Complete combustion manikin system, wh... |
 |
Building material combustion calorific value calorimeter | Building material combustion calorific value calorimeter Mainly used for the detection of stone, wood, concrete, evenly dispersed mineral wool and ... |
 |
Steel Structure Fireproof Coatings | Product Introduction: Heat insulation efficiency and fire resistance test furnace of steel structure fire retardant coatings is a special instrume... |
 |
Carpet Flammability Tester | Standards: BS 4790. ISO 6925. BS 6307 Applications: The Flammability Tester is used to test the effects of a small source of ignition on floor c... |
Same products
 |
Xenon Test Chamber | Seller: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | Seller: Qinsun Instruments Co., LTD | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | Seller: Qinsun Instruments Co., LTD | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | Seller: Qinsun Instruments Co., LTD | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
 |
Flame retardant testing machine | Seller: Qinsun Instruments Co., LTD | Feature highlights: Flame Retardant Tester is designed for testing plastic runway surface layers... |
