Civil Aviation Aircraft Interior Non-metallic Materials Flame Retardant Property Tester

I. Applicability Scope

This system applies to combustion performance testing of non-metallic materials in aircraft cabins:

1.1 Crew/Passenger Cabin Areas:

Including ceiling panels, interior walls, partitions, galley structures, cabinet linings, floor coverings, textiles (curtains/coverings), seat cushions, padding, coated fabrics (decorative/non-decorative), leather products, trays/kitchen equipment, electrical conduits, air ducts, joints/edge covers, B/E class cargo compartment linings, B/C/D/E class cargo floor panels, cargo covers, transparent enclosures, molded/thermoformed components, duct joints/edge trims, etc.

1.2 Non-crew/Passenger Cargo Areas:

Insulation blankets, cargo protective covers, tie-down equipment (including containers, ULDs) for each cargo compartment.

II. Compliance Standards

FAR25.853 (FAA Airworthiness Standards for Transport Category Aircraft)

CCAR-25-R4.853 (Chinese Civil Aviation Regulations Appendix F Part I)

HB5469-2014 (Civil Aircraft Cabin Non-metallic Material Combustion Test Method)

HB5470-2014 (Civil Aircraft Cabin Non-metallic Material Combustion Performance Requirements)

RTCA/DO-160G Section G26.6.2/G26.6.3/G26.6.4 (Environmental Test Procedures)

III. Key Performance Parameters

3.1 Test Types

Vertical burning test

Horizontal burning test

45° inclination burning test

60° inclination burning test (dedicated chamber)

3.2 Equipment Composition

Modular system comprising:

- Combustion chamber

- Control system

- Test fixtures

3.3 Combustion Chamber

Multi-functional chamber with shared structure for vertical/horizontal/45° tests

Independent 60° test chamber

Tempered glass observation window (front panel)

3.4 Burner System

Bunsen burner configuration:

- Nozzle ID: Ф9.5±0.1mm

- Vapor nozzle: Ф0.9±0.03mm

- Air inlet height: 100±10mm

Dual burners with 0°/45°/60°/90° adjustable angles

Flame height adjustment: 20-100mm (test-dependent)

3.5 Timing System

Multi-phase timing (burning/drip flame/smothering phases)

0.1s accuracy with 99.99h max range

3.6 Measurement Systems

Component	Specification
Caliper	1.0mm resolution
Thermocouple	K-type, 1.2-1.5mm diameter
Temperature Meter	0-1000°C range, 1°C resolution
Stopwatch	0.1s precision (backup)

3.7 Fixture System

Stainless steel fixtures with orientations:

- Horizontal test frame

- Vertical test frame

- 45°/60° inclined frames

Other supplier products

	Building Materials Combustibility Test Chamber	Building materialsfire resistance testis a very importantandprofessionaltestin safety engineering. The national standard, GB/T8626-2007. specifies ...
	Building Material Smoke Density Tester	Mainly used for building materials and their products when the static smoke generated by the determination of smoke, is the test of textile materia...
	Fireproof coatings tester	Sample making: 1. The test plate of the fireproof coating tester (small chamber method) is made of birch five-layer plywood conforming to GB738-75...
	Thermal Insulation Rock Wool Thermal Load Tester	Introduction： This equipment determines the temperature at which rock wool insulation shrinks under a specified load when heated at a controlled r...
	Thermal Radiation Flooring Combustion Tester	Product Standards ISO 9239 - 1: Reaction to fire tests for floor coverings - Part 1: Determination of the burning behaviour of floor coverings usi...

All supplier products

Same products

	Xenon Test Chamber	Seller: Standard International Group (HK) Limited	Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli...
	Single Cable Vertical Flame Tester	Seller: Qinsun Instruments Co., LTD	Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ...
	Safety Helmet Flammability Tester	Seller: Qinsun Instruments Co., LTD	Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda...
	Furniture flammability tester	Seller: Qinsun Instruments Co., LTD	Product details Furniture flammability tester is mainly used to test the combustion performance ...
	Flame retardant testing machine	Seller: Qinsun Instruments Co., LTD	Feature highlights: Flame Retardant Tester is designed for testing plastic runway surface layers...