Civil Aviation Aircraft Interior Non-metallic Materials Flame Retardant Property Tester
Product details
I. Applicability Scope
This system applies to combustion performance testing of non-metallic materials in aircraft cabins:
1.1 Crew/Passenger Cabin Areas:
Including ceiling panels, interior walls, partitions, galley structures, cabinet linings, floor coverings, textiles (curtains/coverings), seat cushions, padding, coated fabrics (decorative/non-decorative), leather products, trays/kitchen equipment, electrical conduits, air ducts, joints/edge covers, B/E class cargo compartment linings, B/C/D/E class cargo floor panels, cargo covers, transparent enclosures, molded/thermoformed components, duct joints/edge trims, etc.
1.2 Non-crew/Passenger Cargo Areas:
Insulation blankets, cargo protective covers, tie-down equipment (including containers, ULDs) for each cargo compartment.
II. Compliance Standards
FAR25.853 (FAA Airworthiness Standards for Transport Category Aircraft)
CCAR-25-R4.853 (Chinese Civil Aviation Regulations Appendix F Part I)
HB5469-2014 (Civil Aircraft Cabin Non-metallic Material Combustion Test Method)
HB5470-2014 (Civil Aircraft Cabin Non-metallic Material Combustion Performance Requirements)
RTCA/DO-160G Section G26.6.2/G26.6.3/G26.6.4 (Environmental Test Procedures)
III. Key Performance Parameters
3.1 Test Types
Vertical burning test
Horizontal burning test
45° inclination burning test
60° inclination burning test (dedicated chamber)
3.2 Equipment Composition
Modular system comprising:
- Combustion chamber
- Control system
- Test fixtures
3.3 Combustion Chamber
Multi-functional chamber with shared structure for vertical/horizontal/45° tests
Independent 60° test chamber
Tempered glass observation window (front panel)
3.4 Burner System
Bunsen burner configuration:
- Nozzle ID: Ф9.5±0.1mm
- Vapor nozzle: Ф0.9±0.03mm
- Air inlet height: 100±10mm
Dual burners with 0°/45°/60°/90° adjustable angles
Flame height adjustment: 20-100mm (test-dependent)
3.5 Timing System
Multi-phase timing (burning/drip flame/smothering phases)
0.1s accuracy with 99.99h max range
3.6 Measurement Systems
3.7 Fixture System
Stainless steel fixtures with orientations:
- Horizontal test frame
- Vertical test frame
- 45°/60° inclined frames
Send product request
Other supplier products
 |
Sand and Dust Test Chamber for Automotive Connectors | The sand and dust test chamber for automotive connectors meets the requirements of protection - class tests for the enclosures of household applian... |
 |
Fatigue Endurance Tester for Dental Implants | Standard ISO 14801:2016: Specifies dynamic fatigue testing protocols for endosseous dental implants, including load ratios, frequency, and failure... |
 |
Air - tightness Testing Device for Automotive Connectors | The air - tightness testing device for automotive connectors uses the pressure principle to conduct non - destructive tightness tests on containers... |
 |
Photovoltaic module damp heat test chamber | Standard IEC 61215: Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval UL 1073: Standard for Safety for Enclosu... |
 |
Falling Sand Abrasion Tester | Standards GB811-2022. GB24429 GB/T 38305 GJB1564A GA/T44. GA293 GA294 GA295 GA296 ASTMD968 ASTMD333 ASTMD1395 ASTMD2205 Main applicati... |
Same products
 |
Xenon Test Chamber | Seller: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | Seller: Qinsun Instruments Co., LTD | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | Seller: Qinsun Instruments Co., LTD | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | Seller: Qinsun Instruments Co., LTD | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
 |
Flame retardant testing machine | Seller: Qinsun Instruments Co., LTD | Feature highlights: Flame Retardant Tester is designed for testing plastic runway surface layers... |
