Car seat static strength tester
Applicable standards:
GB 11550-2009"Car seat headrest strength requirements and test methods" : This standard specifies the static strength test requirements and test methods of car seat headrest, which is suitable for the static strength test of car seat headrest.
GB 15083-2006"Strength requirements and test methods for car seats, seat fixtures and headrests" : This standard provides static strength test methods and requirements for car seats, seat fixtures and headrests, covering seat backs, seat cushions, headrests and other components.
Main parameters:
Load measurement range:The load measurement range of the tester is usually between （40 to 2000）N, depending on the model and configuration of the tester. This parameter determines the maximum and minimum loads that the tester can measure.
Load accuracy:Load accuracy is usually expressed as the percentage error of the measured value, generally around ±1%. This parameter reflects the accuracy and reliability of measuring load of the tester.
Load cylinder stroke:The load cylinder stroke refers to the maximum distance that the tester can move during the loading process, usually around 500mm. This parameter determines the range of loads that the tester can simulate.
Displacement accuracy and resolution:Displacement accuracy is usually expressed as a percentage error or absolute error of the measured value, while displacement resolution refers to the smallest change in displacement that the tester can detect. These parameters affect the accuracy and sensitivity of measuring displacement.
Angular displacement measurement and control accuracy:For test items that need to measure angular displacement, the tester should have sufficient angular displacement measurement and control accuracy, usually around ±0.01°. This parameter reflects the accuracy and stability of the tester when measuring angular displacement.
Sampling frequency:Sampling frequency refers to the rate at which the tester collects data during the test, usually around 1000Hz. The high sampling frequency ensures that the tester can capture more data points, which improves the accuracy and reliability of the test.
Equipment power supply:The tester usually needs a single-phase AC220V, 50Hz power supply, the power depends on the tester model and configuration.
Software functions:The tester is usually equipped with professional test software for controlling the test process, collecting and processing data. The software functions should include manually setting conditions to find the feature points of the curve, obtaining the slope between two points of any curve, scaling and moving the curve, exporting all test sampling points to Excel, etc.
Send product request
Other supplier products
 |
Shoelace anti-siphon tester | Product Introduction Shoelace anti-siphon tester is suitable for all kinds of waterproof leather, leather, mesh, waterproof shoelace, ribbon water... |
 |
Thermal Insulation Materials Adhesive Strength Tester | Meet the standard: JGJ144-2004 "External Wall insulation engineering Technical Regulations" JG158-2004 "Rubber powder polystyrene particles exter... |
 |
Fabric Downproof Tester(Rolling Box) | Standards GB/T 12705.1:Textile -Methods of testing the down-proof properties of fabrics- Part 1: Rubbing test; GB/T 14272：Requirements of down ... |
 |
High temperature creep endurance testing machine | Product Introduction: The high temperature creep endurance testing machine is mainly used for testing the mechanical properties of superalloys, ti... |
 |
Leakage trace tester | I. Product Overview TheLeakage Trace Testeris a precision diagnostic tool designed to visually identify and analyze fluid/gas leakage paths in sea... |
Same products
 |
Seat Bumping and Creep Test Bench | Seller: Standard International Group (HK) Limited | This test bench is used for simulating the car seat bumping and creep situation when a car is run... |
 |
Automobile seat belt fixed point test bench | Seller: Standard International Group (HK) Limited | Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtur... |
 |
Impact strength tester for car seat headrest | Seller: Standard International Group (HK) Limited | Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requi... |
 |
Impact strength tester for car seat launching headrest | Seller: Standard International Group (HK) Limited | Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, w... |
 |
Automobile Headrest Strength Tester | Seller: Standard International Group (HK) Limited | Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test me... |
