Wireless Transmission Steel Bar Ultrasonic Flaw Detector
Steel bar is a conventional product with high density, moderate noise. The system is suitable for the automatic detection of internal and external defects of various steel bars.
The principle of UT ultrasonic flaw detection is that after the ultrasonic wave is coupled into the steel rod by water, the incident propagation will case ultrasonic reflection when there is a defect in the bar. The ultrasonic instrument will alarm the ultrasonic reflected signal after the amplified signal to realize the automatic detection of the defect.
Wireless Transmission Steel Bar Ultrasonic Flaw Detector Brief Introduction
There are two probe regulators in section 1,180 degrees apart. Each regulator is equipped with a two-channel combination of ultrasonic line focus probes, and the transverse wave incident clockwise.
Detection of defects: detection of round subcutaneous defects in a rounded clockwise direction
Center frequency: 5.0MHz ± 10%
Coupling method: water immersion method
Quantity: 2 sets of probes, each set consisting of 2 combined wafers, which are evenly distributed in the circumferential direction of the workpiece, 180° apart, on the same section. A total of 4 independent channels.
A total of 2 probe adjustment frames are placed on section 2, each separated by 180°, and a 2-channel combined ultrasonic line focusing probe is arranged on each adjustment frame, and the longitudinal wave is incident.
Detection of defects: metallurgical defects inside the steel bar,
Detection range: center transverse hole.
Center frequency: 5.0MHz ± 10%
Coupling method: water immersion method
Quantity: 2 sets of probes, each consisting of 2 combined wafers. These 2 sets of probes are evenly distributed in the circumferential direction of the workpiece, 180° apart, and there are 4 independent channels in the same section.
A total of 2 probe adjustment frames are placed on section 3, each separated by 180°, and a 2-channel combined ultrasonic line focusing probe is arranged on each adjustment frame, and the transverse wave is incident counterclockwise.
Detection of defects: counter-clockwise detection of round subcutaneous defects
Center frequency: 5.0MHz ± 10%
Coupling method: water immersion method
Quantity: 2 sets of probes, each consisting of 2 combined wafers. These 2 sets of probes are evenly distributed in the circumferential direction of the workpiece, 180° apart, and there are 4 independent channels in the same section.
Defect detection standard
GB/T4162-2008 Ultrasonic testing method for forged steel bar.
Wireless Transmission Steel Bar Ultrasonic Flaw Detector Parameters
|
Channel number |
12 channels |
|
Flaw detection speed |
30m/min |
|
Total gain |
100dB，step0.5dB |
|
Working mode |
Single probe transmitting, receiving or double probe transmitting and receiving respectively |
|
Sensitivity margin |
≥50dB |
|
Resolving power |
≥26dB |
|
Dynamic range |
≥30dB |
|
scan range |
0～5000mm |
|
Frequency range |
|
|
Sampling range |
250MHz |
|
Repetition range |
Single channel100Hz～4KHzadjustment |
|
Vertical linearity |
≤2% |
|
Horizontal linearity |
≤1% |
|
Detection mode |
Full-wave, positive half-wave, negative half-wave |
|
Gate setting |
Each channel has three gates, A and B are defective gates and C are interface tracking gates. |
|
Alarm indication |
Color Display and Sound Alarm of A, B and C Gate Alarm on Each Channel |
|
Delayed alarm |
Two path,delay time 0.1-10s,step 0.1s |
|
Waveform storage, unlimited number, waveform playback, printing and report generation. |
|
BKNis a professionalmfl suppliers. We provide Eddy Current Testing, Magnetic Flux Leakage Testing, ndt device, ndt testing, ultrasonic metal testing equipment, ultrasonic bar testing, ultrasonic metal testingand so on. Want to know more? Please contact us.
Отправить запрос, связаться с поставщиком
Другие товары поставщика
|
|
Wireless Transmission Steel Bar Ultrasonic Flaw Detector | Steel bar is a conventional product with high density, moderate noise. The system is suitable for the automatic detection of internal and external ... |
 |
EDM Notch | Nanjing BKN Automation System Co., Ltd., originated from the eddy current testing laboratory of the Nanjing University of Technology. It is an eddy... |
 |
Portable Magnetic Flux Leakage Testing Equipment | Magnetic flux leakage test refers to the formation of a leakage magnetic field on the surface of a test piece after it is magnetized due to defects... |
 |
RQ-120-B Automatic CNC EDM Notch | BKNis one of professional ultrasonic testing equipment manufacturers. We provide Magnetic Flux Leakage Testing, eddy current testing and so on. Wan... |
 |
Steel Pipe Testing | Steel having a hollow section that is much longer than the diameter or circumference. According to the cross-sectional shape, it is divided into ro... |
Похожие товары
 |
Cable Wire Recycling Production Line | Продавец: Changzhou Optima Technology Co.,Ltd. | Cable Wire Recycling Production Line 1000kg Copper Wire Recycling Machines: The biggest ca... |
 |
Small Cable Granulator and Separator | Продавец: Changzhou Optima Technology Co.,Ltd. | Small Cable Granulator and Separator : Small shape,1 phase power,grind and separate copper f... |
 |
Turnkey service of tire recycling | Продавец: Changzhou Optima Technology Co.,Ltd. | Turnkey service of tire recycling At , we specialize in manufacturing advanced tire recyclin... |
 |
Mobile Portable Tire Shredder | Продавец: Changzhou Optima Technology Co.,Ltd. | Mobile Portable Tire Shredder Mobile Portable Tire Shredder – A cost-effective soluti... |
 |
Aluminum wire rod rewinding machine | Продавец: Changzhou Optima Technology Co.,Ltd. | Aluminum wire rod rewinding machine Basic Introduction 's is engineered with advanced Korea... |
