Air Cooling CNC Vacuum Pump

• 

Air-cooled vacuum pump
HYCNC
5.5/7.5/11kw
5.5KW:345v/415v 7.5KW:345v/415v 11KW:380v
50hz
5.5KW:-34/50kpa 7.5KW:-35/56kpa 11KW:62kpa
5.5KW:12A /14.4A 7.5KW:15.5A/18.6A 11KW:21.5A
5.5KW:520m³/h 7.5KW:550m³/h 11KW:1100m³/h
Shandong Jinan

Product Introduction and Description of Air Cooling CNC Vacuum Pump
Product introduction and description:

Applicable scenarios: CNC router

Product Composition:

Installation and operation tips of CNC router vacuum adsorption pump:

Similar to the water cooled vacuum pump produced by HYCNC, the vacuum adsorption plate or table of the air cooling CNC vacuum pump also requires the customer to groove the groove. After the groove is grooved, flange joints are installed in each area. The most common is 6 areas (which can be partitioned according to customer needs). 6 pcs flange joints are then connected to the pipe. Then, connect the 6 pcs valve onto the 6-way connector, and connect the wire pipe from the 6-way connector to the cnc router vacuum pump.

Advantages of air cooling vacuum pump:

1. Small size and easy installation

2. Maintenance: no consumables, convenient and efficient, and cost-saving

3. Low noise

4. Wide suction range, mainly depends on cnc vacuum pump power

Tips: CNC router recommends to use vacuum pump of more than 4kw. Generally, CNC router adsorption platform uses power options of 5.5kw, 7.5kw, and 11kw. The smaller the power, the smaller the suction power. Thus, it is not recommended to use less than 4kw.

Influencing factors of air cooled vacuum pump suction has the flowing: The vacuum pressure of the vacuum pump is the same. The only difference is th flow speed. If the force is not enough, the easiest way is to increase the suction cup.

If the air leakage is serious during adsorption, the flow should be increased by increasing the vacuum pump power; if the intensity is not enough, the adsorption area should be increased; if the adsorption area is large, the thin plate will then deform. Thus, under this circumstance, you should choose multiple suction ports.

As a reliable cnc router parts manufacturer, we provide cnc machine spares, spindle motor air cooled, cnc air coolingand etc. Want to buy spindle motoror know more? Please contact us.

Другие товары поставщика

	CW5200 Industrial Water Chiller	product name: cw5200 Industrial water chiller Brand: Hongyang / HYCNC model: CW5200 single in single out CW5200 double in and do...
	ER Nut	At here, we mainly sell the following products: spindle motors, inverters, stepper motors, hybrid servo motors, drives, guide rails, sliders, gear ...
	Air Cooling CNC Vacuum Pump	Air-cooled vacuum pump HYCNC 5.5/7.5/11kw 5.5KW:345v/415v 7.5KW:345v/415v 11KW:380v 50hz 5.5KW:-34/50kpa 7.5KW:-35/56kpa 11KW:62kpa 5.5KW:12A /14.4...
	Changsheng 2.2kw ER20 Round Air Cooled Spindle Motor	model: GDZ-80F-2.2B Dimensions: Φ80*195 Rotating speed: 24000RPM power: Voltage: ...
	Er Collet/Nuts	At here, we mainly sell the following products: spindle motors, inverters, stepper motors, hybrid servo motors, drives, guide rails, sliders, gear ...

Похожие товары

	Резервуар с жидким азотом для Боснии и Герцеговины для лаборатории KGSQ	Продавец: Хэнань Тяньчжидао Биотехнология Лтд.	В лабораториях чаще всего используются резервуары с жидким азотом, имеющие большую вместимость, б...
	Хранение сперматозоидов в Танзании Сосуд KGSQ ln2	Продавец: Henan Tianzhidao Biological Technology Co., Ltd.	В лабораториях чаще всего используются резервуары с жидким азотом, имеющие большую вместимость, б...
	Ebike Battery	Продавец: Shenzhen Worldpower Energy Storage Technology Co.,Ltd	Custom Ebike Lithium Battery Manufacturer Elevate your electric biking experience with Worldpowe...
	Battery Energy Storage Systems	Продавец: Shenzhen Worldpower Energy Storage Technology Co.,Ltd	Battery Energy Storage Systems (BESS) are cutting-edge technologies that store electrical energy ...
	ETH Ethereum Jasminer X4 BRICK ASIC Miner	Продавец: Shenzhen Dovina Electronic Co.,Ltd	Jasminer X4 Brick Review Jasminer x4 brick for salefrom Jasminer mining EtHash algorithm with a ...