Air Cooling CNC Vacuum Pump
Air-cooled vacuum pump
HYCNC
5.5/7.5/11kw
5.5KW:345v/415v 7.5KW:345v/415v 11KW:380v
50hz
5.5KW:-34/50kpa 7.5KW:-35/56kpa 11KW:62kpa
5.5KW:12A /14.4A 7.5KW:15.5A/18.6A 11KW:21.5A
5.5KW:520m³/h 7.5KW:550m³/h 11KW:1100m³/h
Shandong Jinan
Product Introduction and Description of Air Cooling CNC Vacuum Pump
Product introduction and description:
Applicable scenarios: CNC router
Product Composition:
Installation and operation tips of CNC router vacuum adsorption pump:
Similar to the water cooled vacuum pump produced by HYCNC, the vacuum adsorption plate or table of the air cooling CNC vacuum pump also requires the customer to groove the groove. After the groove is grooved, flange joints are installed in each area. The most common is 6 areas (which can be partitioned according to customer needs). 6 pcs flange joints are then connected to the pipe. Then, connect the 6 pcs valve onto the 6-way connector, and connect the wire pipe from the 6-way connector to the cnc router vacuum pump.
Advantages of air cooling vacuum pump:
1. Small size and easy installation
2. Maintenance: no consumables, convenient and efficient, and cost-saving
3. Low noise
4. Wide suction range, mainly depends on cnc vacuum pump power
Tips: CNC router recommends to use vacuum pump of more than 4kw. Generally, CNC router adsorption platform uses power options of 5.5kw, 7.5kw, and 11kw. The smaller the power, the smaller the suction power. Thus, it is not recommended to use less than 4kw.
Influencing factors of air cooled vacuum pump suction has the flowing: The vacuum pressure of the vacuum pump is the same. The only difference is th flow speed. If the force is not enough, the easiest way is to increase the suction cup.
If the air leakage is serious during adsorption, the flow should be increased by increasing the vacuum pump power; if the intensity is not enough, the adsorption area should be increased; if the adsorption area is large, the thin plate will then deform. Thus, under this circumstance, you should choose multiple suction ports.
As a reliable cnc router parts manufacturer, we provide cnc machine spares, spindle motor air cooled, cnc air coolingand etc. Want to buy spindle motoror know more? Please contact us.
在线联系供应商
Other supplier products
 |
Electrical Components | As a professional manufacturer that specializes in the production of various types of CNC machine components, HYCNC sells cnc router electronicslik... |
 |
CNC Parts | WHERE THERE IS A CNC MACHINE, THERE IS A HYCNC PRODUCT. Jinan Hongyang CNC machinery Co., Ltd. is committed to providing a one-stop purchase servic... |
 |
CNC 15pin Handwheel Controller | CNC Hand Controller Product Name: Cnc 15pin Handwheel Controller Operating Voltage: 5v、12v、24v Applicable Syst... |
 |
CNC Router Inverter | Employing advanced frequency conversion technology and microelectronic technology, the CNC router invertercan effectively change the frequency and ... |
 |
ER Nut | At here, we mainly sell the following products: spindle motors, inverters, stepper motors, hybrid servo motors, drives, guide rails, sliders, gear ... |
Same products
 |
Microcrystalline wax used for shoe polish processing | 卖方: Syntop chemical Co.,Ltd. | Microcrystalline wax is commonly used in shoe polish, primarily to harden the formula, adju... |
 |
Microcrystalline wax used for rubber plastic processing and modification | 卖方: Syntop chemical Co.,Ltd. | Microcrystalline wax has a wide range of industrial applications, primarily in the areas of rubbe... |
 |
Microcrystalline wax 80A used for lubrication and demolding | 卖方: Syntop chemical Co.,Ltd. | The core industrial applications of microcrystalline wax 80A are primarily focused on rubber prot... |
 |
Tyvek Flat Roll Pouch | 卖方: Hopeway AMD | Tyvek Flat Roll Pouch is designed for professional sterilization packaging, offering clean handli... |
 |
Industrial Warehouse Ceiling Fans | 卖方: Hebei Windmax Power Technology Co., Ltd. | Industrial Warehouse Ceiling Fans Industrial Warehouse Ceiling Fans for Warehouses, Logisti... |
