1U EDFA Equipment
The main function of the EDFA optical amplification subsystem launched by Guangzhou Sintai Co., Ltd is to compensate the signal's optical power in the transmission link, which can finally extend the optical signal transmission distance.
It can be divided into BA, LA, and PA based on the application scene. BA is usually used at the transmitting end to boost the output optical power of the system. LA is usually used at the repeater section to compensate for the power loss of the line. PA is usually used at the receiving end of the system to improve the input optical power.
The EDFA can amplify all the input optical signals by using the erbium-doped fiber as the gain medium and using the 980nm or 1480nm pump laser as the pump source with one-stage or two-stage amplification. It's one of the most indispensable and important parts of the DWDM system, high-speed transmission system, and all-optical network in the future.
1U EDFA Equipment Feature
Support the unified amplification of the 48CH/96CH DWDM signal of the C band.
Automatic gain control(AGC).
Flat gain and low noise figure.
Support built-in VOA and automatic adjustment of optical power.
Support two-stage amplification with OADM or DCF modules to be configured in the line.
1U pluggable rack, flexible capacity configuration.
Support AC power 220V, DC power -48V, and 1+1 power input protection.
Free of configuration installation and support plug and play.
Support multi-kinds of graphical interface network management, such as SNMP, Web.
1U EDFA Equipment Specification
Item Parameter Remark
Working wavelength range Stand type: 1529nm~1561nm, extended type: 1528nm~1568nm
EDFA type BA LA PA
Min input power (typical) -22dBm -30dBm -32dBm
Saturation output power (typical) +20dBm +20dBm +16dBm To be customized with max +23dBm
Rated gain (typical) 17dB 25dB 20dB To be customized
Gain flatness ≤1.5dB
Noise figure ≤5.5 dB
Working temperature range -10℃~60℃
Working humidity range 5%~95% no condensation
Storage temperature -40℃~85℃
Equipment dimension 1U: 44 mm (H)×442 mm (W)×280 mm (D)
Network management Support multi-kinds of graphical interface network management, such as SNMP and Web Optional
Special technology Built-in VOA with automatic adjustment of optical power Optional
Optical interface LC/UPC
Power supply AC: 90 ~ 260V or DC: -36 ~ -72 V (1+1 power input backup)
Typical power consumption Full configuration<60W
Heat dissipation Fan cooling
MTBF ＞100000 hours
For more information about optical communication devices, please feel free to contact us!
Other supplier products
|
|
10G SFP+ DWDM Transceiver |
Designed for Ethernet, Fiber Channel, SDH, SONET, CPRI, or OTN links over duplex single-mode fibers, the Sintai DWDM 10GSFP+ optical transceivers u... |
|
|
4CH CWDM Mux Demux |
CWDM Coarse Wave Division Multiplexing (CWDM) Multiplexer/Demultiplexer (MUX/DEMUX) modules support ITU-T G.694.2 wavelengths between 1270nm to 161... |
|
|
10 SFP+ C/DWDM Transponder |
10GTransponder
10G otn transponderservice card launched by Sintai Communication Co., Ltd. supports four types of service access with 42M~11.3G rat... |
|
|
Integrated WDM System |
The integrated WDM System offers 1U 48X10G→480G System and 1U 12X100G→1.2T System which supports single-channel access rate up to 10 Gbit... |
|
|
DWDM Mux Demux |
01- 4CH DWDM Mux Demux
DWDM Mux Demux is usually used for long-haul transmission where wavelengths are packed tightly together over the C-band, up ... |
供应产品
Same products
