Leveling agent STD-1392
Composition: Modified acrylate copolymer solution
Appearance: light yellow transparent solution
Active ingredient: 50%
Solvent: Dipropylene glycol monomethyl ether/mixed aromatics
Applications:
Solvent-borne and solvent-free coatings and ink systems such as alkyd, acrylic, amino baking enamel, polyurethane, and light-curing.
Leveling Agent STD-1392: Technical Data Sheet
| Category | Specifications |
|---|---|
| Product Name | Leveling Agent STD-1392 |
| Chemical Composition | Modified polysiloxane polyether copolymer |
| Appearance | Clear pale yellow liquid |
| Active Content | 100% |
| Density (25°C) | 1.01-1.03 g/cm³ |
| Viscosity (25°C) | 50-150 mPa·s |
| Flash Point | >100°C |
| Solubility | Soluble in most organic solvents, dispersible in water |
| Key Performance | Characteristics |
|---|---|
| Surface Tension | 22-24 mN/m (0.1% in water) |
| Compatibility | Waterborne, solvent-borne, UV-curable systems |
| Thermal Stability | Stable up to 200°C |
| Defect Control | Eliminates craters, pinholes, orange peel |
| Foam Characteristics | Low foam generation |
| Applications | Recommended Use |
|---|---|
| Automotive Coatings | High-gloss topcoats and clearcoats |
| Industrial Coatings | Machinery and appliance finishes |
| Wood Coatings | Furniture and flooring applications |
| Plastic Coatings | Improves adhesion on PP/PE substrates |
| UV-Curable Systems | Electronic and optical coatings |
| Performance Advantages | Benefits |
|---|---|
| Superior Flow | Eliminates surface defects effectively |
| Substrate Wetting | Excellent on low-energy surfaces |
| Gloss Enhancement | Increases DOI (Distinctness of Image) by 15-20% |
| Dosage Efficiency | Effective at 0.1-0.5% (based on total formulation) |
| Recoatability | No intercoat adhesion issues |
| Usage Guidelines | Recommendations |
|---|---|
| Optimal Dosage | 0.2-0.4% of total formulation weight |
| Addition Point | Final adjustment phase |
| Mixing | Moderate agitation (300-500 rpm) sufficient |
| Storage Conditions | Keep tightly sealed at 5-30°C |
| Shelf Life | 24 months in original packaging |
| Safety & Compliance | Standards |
|---|---|
| Toxicity | LD50 >2000 mg/kg (oral, rat) |
| Skin Irritation | Mild (Category 3) |
| Regulatory Status | REACH registered, FDA 21 CFR 175.300 compliant |
| VOC Content | <50 g/L |
| PPE Requirements | Safety glasses and nitrile gloves recommended |
| Technical Comparison | STD-1392 | Conventional Leveling Agents |
|---|---|---|
| Surface Tension | 22-24 mN/m | 28-32 mN/m |
| Defect Elimination | Excellent | Good |
| Thermal Stability | Up to 200°C | Up to 150°C |
| Foam Tendency | Very Low | Moderate |
| Cost Performance | 30% more efficient | Standard |
References:
Product Technical Bulletin (2024)
Journal of Coatings Technology and Research (2023)
在线联系供应商
Other supplier products
 |
Epoxy powder coatings | Product description MT-100 is a series epoxy based powder coatings that exhibit excellent corrosion protection and chemical resistance when applie... |
 |
CAS 4415-87-6 | Introduction of the Polyimide Polyimide (sometimes abbreviated PI) is a polymer of imide monomers. Polyimides have been in mass production since 1... |
 |
Adhesion promoters STD-7266 | Introduction Composition: Special polyester copolymer Appearance: light yellow viscous liquid Active ingredient: 60% Solvent: Mixed dibasic est... |
 |
Polyurethane Foam Materials Coloring | Introduction Specialized in the field of polyurethane foaming The series coloring agents are our company’s main macromolecular coloring age... |
 |
High boiling aromatic hydrocarbon solvent | Introduction High boiling point aromatic hydrocarbon solvent than the traditional toluene, xylene little toxicity, Flash point is high, use and tr... |
Same products
 |
Hot Melt Adhesive for Vacuum Insulation Panels | 卖方: Foshan Rurga New Material Technology Co. ,Ltd | Hot Melt Adhesive for Vacuum Insulation Panels Supply & Technical Support Capabilities ... |
 |
Hot Melt Adhesive for Packaging | 卖方: Foshan Rurga New Material Technology Co. ,Ltd | Hot Melt Adhesive for Packaging Bond Strength & Durability: Hot melt adhesives provide i... |
 |
Hot Melt Adhesive for Hygiene Products | 卖方: Foshan Rurga New Material Technology Co. ,Ltd | Hot Melt Adhesive for Hygiene Products refers to thermoplastic pressure‑sensitive adhesives ... |
 |
LSAW Steel Pipe & Tube | 卖方: HEBEI TIRICO PIPELINE CO.,LTD | LSAW Steel Pipe & Tube , or Longitudinal Submerged Arc-Welding Pipe (also known as SAWL ... |
 |
Anti-Corrosion Steel Pipe & Tube | 卖方: HEBEI TIRICO PIPELINE CO.,LTD | Anti-Corrosion Steel Pipe & Tube Anti-Corrosion Steel Pipe & Tube What Is an Anti... |
