Control Box-Feeder Terminal Unit
The feeder remote terminal unit(FTU) is a new HV switch control device of control cabinet enclosures equipped with both the imported DSP high-speed sampling chips and the high-performance ARM chips, and can fast and stably finish the monitoring on the switch.
Industrial feeder terminal unitby ourelectric power equipment companyhas such functions as the protection, measuring, controlling, monitoring, communication, remote control, and so on and features high integration level, flexible configuration, and user-friendly interface. Electrical control cabinet are widely applied to the radiant and ring network power supply systems.
FTU outdoor control electrical control box can help the systems identify transient and permanent line faults. Outdoor control box eliminate the impact of transient line faults automatically, isolate the permanent fault segments to avoid prolonged power failure in a large area, and automatically recover the power supply in fault-free areas, so as to realize the automation of power distribution network in an economical and practical way.
Key Functions of Control Box-Feeder Terminal Unit
|
S/N |
Functions |
Remarks |
|
Three section protection |
Each protection can be vote back independently |
|
|
Over-current count protection |
Failure time count, output after meeting the number of times, output mode is optional |
|
|
Zero-sequence protection |
Output options: exit, alarm and tripping |
|
|
Pre - voltage fault protection |
Protection can be accelerated when combined at fault point |
|
|
Post-reclosing acceleration |
Vote back independently |
|
|
Constant time-lag |
The protection time is fixed |
|
|
Inverse time limit |
Multiple protection curves optional |
|
|
Ring network protection |
Hardware needs to configure double PT |
|
|
Event Log |
The recording time is exactly millisecond |
|
|
Status enquiry |
The main content is remote control and remote metering |
|
|
Remote programmable |
Remote input support programmable |
Communication Protocols of Control Box-Feeder Terminal Unit
|
S/N |
Protocols |
Remarks |
|
IEC balanced |
||
|
IEC unbalanced |
||
|
IEC |
||
|
Now support level 3 |
||
|
Modbus |
Technical Parameters of Control Box-Feeder Terminal Unit
|
Items |
Rated value |
Remarks |
|
|
Operating ambient temperature |
-40 ~ +85℃ |
||
|
Environmental relative humidity |
10 ~ 100% |
||
|
Maximum absolute humidity |
35g/m3 |
||
|
Atmospheric pressure |
66~ 108kPa |
||
|
Working voltage |
AC220V±20% |
||
|
Working voltage frequency |
50HZ±5HZ |
||
|
Power consumption |
≤15W |
||
|
Protective exit time |
<35ms |
Protect inherent action time at 1.5 times fixed value |
|
|
Insulation impedance |
>100MΩ/ DC500V |
||
|
Power frequency withstand voltage |
2k |
Power circuit to ground |
|
|
500 |
On-off input circuit to ground |
||
|
500 |
Output circuit to ground |
||
|
2k |
AC circuit to ground |
||
|
2k |
AC circuit and power circuit |
||
|
1500 |
Between on-off input circuit and output circuit |
||
|
Impulse withstand voltage |
5k |
Power circuit to ground |
|
|
1k |
On-off input circuit to ground |
||
|
1k |
Output circuit to ground |
||
|
5k |
AC circuit to ground |
||
|
5k |
AC circuit and power circuit |
||
|
1k |
Between on-off input circuit and output circuit |
Characteristic Functions of Control Box-Feeder Terminal Unit
Feeder terminal unitis small in size and large in quantity. FTU electrical control cabinetis equipped with a transmitter for direct AC sampling. It is resistant to high temperature and cold and is suitable for outdoor harsh environments.
Unlike thescada remote terminal unit, the amount of data collected by FTUelectronic control box is small, the requirement of communication rate is low, and the requirement of reliability is high.
FTUoutdoor control boxcan be manufactured by a high-performance single-chip microcomputer. In order to adapt to the harsh environment, industrial chips that can work at 75 ℃ shall be selected, and they shall be protected against lightning, rain and moisture through appropriate structural design.
Application of Control Box-Feeder Terminal Unit
At present, feeder terminal units power control box as one popular type ofdistribution electrical boxhave been widely deployed in column switches, ring network cabinets, switching stations, power control boxes, and other places on the distribution network line to realize the "three remote" automation functions of remote signaling, telemetry and remote control of remote primary equipment.
As an information and data communication tool, a computer network provides a powerful communication means forindustrial electrical cabinetand provides a reliable basis for realizing the networked control of distribution automation system devices. Fieldbus technology and GPRS wireless communication technology inject new vitality into the implementation of feed automation. Driven by network, communication and other information technologies, distribution automation is developing from spontaneous Island automation to unified and systematic comprehensive automation.
Gopower as a electric power equipment company,has participated in the construction of an intelligent control project of transmission and distribution in the world-renowned Olympic Project together with Huayi Electric Gas.
在线联系供应商
Other supplier products
 |
Pole Mounted Switch | The pole mounted disconnect switchis a kind of safety switch used on the electric pole to ensure the safety of electricity. Its main function is to... |
 |
33KV SF6 Gas Load Break Switch | Application of 33KV SF6 Gas Load Breaker Switch The switch is made of a proven rugged, corrosion-resistant material (304L stainless steel plate fo... |
 |
VCB Pole Mounted Recloser | ZW32 series automatic circuit line recloser, produced by our vacuum circuit breaker company, are used in distribution systems. Auto distribution li... |
 |
Recloser Control Box-Feeder Terminal Unit | Recloser Control Box-Feeder Terminal Unit The feeder terminal unit(FTU) is a new HV switch control device of control cabinet enclosures equipped w... |
 |
SF6 Gas 11 KV Load Break Switch | The 11 kv load break switch is suitable for the distribution network with the highest voltage 11kV, the rated current 630A, and the rated frequency... |
