stacking machine using vacuum cap crane

Panel stack wrapped
The panel stack wrapper wraps a stack of sandwich panels with a plastic film to protect the stack during transport. This wrapper wraps the film around the stack in a spiral motion but does not pack ends of panels (this is a manual operation). Film spool changing time is approximately at 30 seconds. This wrapper wraps the film around the stack in a spiral motion.

The leg insertion unit load EPS legs for transport under panel stacks by the operator. The leg position for each stack is preprogrammed by the machine operator and the machine automatically places a EPS leg under the stack as per the operator program. The leg is pushed from under the magazine onto the transfer conveyor. Through encoder positioning, the transfer conveyor drives the leg in unison with panel stack and wraps the leg in with the pack in the correct position.

General specification:
Minimum panel length: 3.5 meter
Maximum panel length: approximately 12.5 meter
Panel thickness: 40-200 mm
Panel stack: up to 1.1 meter high
Maximum panel width: 1250 mm
Operating speed: approximately 0-5m/min
Dimensions: 14m*2.7m*2.6m
Weight: about 5 tons
Bore diameter of the wrapper ring: 1828mm
Use PE film with width 500mm, 18-30um. (each coil no more than 15kg,1500m. Inner diameter 76mm)
The overlapping area of film wrapping is between 0-300mm(adjustable).
The pre stretching rate of film should be not less than 150%.
Automatically increase the times of wrapping at the front and end of package.
Rollers of conveyers are 700mm high from the ground.
Mitsubishi inverters, PLC and touch screen, Schneider/Omron low voltage apparatus.
 Automatic blocks filling system. (Filling block: length 900~1200mm, width 200mm, height 100mm)
Centralized electric control.
Length of conveyers: 12m.
Tension control system for film.

The wrapper consists of the following major items:
Rotating housing for application of film
Spool carriage
Automatic film clamping system
Automatic film cutting system
Control system for operation of system
Internal conveyor to allow pallets to be wrapped with the panels
EPS leg magazine storage and supply unit
Computer control system

A conveyor is position just prior to the wrapper to feed stacks into the wrapper. This conveyor will be a rubber roller type system. A slat type conveyor is also positioned after the wrapper to allow panel stack to be removed after wrapping.

Wrapper operation is as follow:
A stack of panels is presented to the input conveyor from the panel stacker noted above.
The input conveyor feeds the leading edge of the stack into the rotating housing
The wrapper ring automatically starts to allow the leading edge of the stack to be wrapped, wrapping it several times for strength
The input conveyor which feeds the stack through the wrapper. The stack is spirally wrapped at the preset feedrate.
The trailing edge of the panel reaches the end of the wrapping ring and the conveyor stop, allowing extra wraps at the end of the panels.
The automatic film cutting system cuts the film automatically and grips it, making it ready for the next cycle.
The panel stack is driven out to the exit and where it automatically stops and awaits removal by forklift truck by the operator

Leg insertion unit operation is as follows:
As the stack of panels is fed into the wrapper, an EPS leg is fed from the magazine onto a conveyor under the panel stack.
An encoder measures the stack position and the leg is automatically fed under the panel stack to a pre-programmed position under the stack.
The conveyor continues to drive the EPS leg at the same speed under the panel stack as it is wrapped into the pack by the wrapper.
As more legs are required, the system continues to feed EPS legs under the stack as required.

Panel wrapper exit conveyor
A 11m long slat type exit conveyor removers wrapped product from the wrapper and presents it to the operator for remove.



在线询价

至: Shanghai Yongming Machinery Manufacturing CO., LTD.
Your E-mail:
消息正文:


Send to other suppliers

Other supplier products

Garage Door roll forming machine with hydraulic profile cutter
Garage Door roll forming machine with hydraulic profile cutter Garage door roll forming machine could make garage door profile steel sheet. It could be used independently or used in whole sandwich panel line. E...
EPS and rockwool /mineral wool /glasswool sandwich panel product line
EPS and rockwool /mineral wool /glasswool sandwich panel product line  EPS and rockwool /mineral wool /glasswool sandwich panel line could make rock wool,mineral wool,glasswool,EPS sandwich panel for wall and roo...
Mixing head with cross beam spraying PU foam
Mixing head with cross beam spraying PU foam Mixing head on cross beam (single head) The PUR foam mixture lay down is provided by means of a mixing and foaming head mounted on a cont...
 PUR/PIR /Polyurethane sandwich panel product line
 PUR/PIR /Polyurethane sandwich panel product line PUR, PIR (Polyurethane) sandwich panel product line continuous make the PUR,PIR  sandwich panel with the thickness 50mm-200mm.The main composi...
Wall roll forming machine with hydraulic profile cutter
Wall roll forming machine with hydraulic profile cutter Wall roll forming machine could make wall profile steel sheet. It could be used independently or used in whole sandwich panel line. Edge Joint Roll...
供应产品

Same products

Crimping Machine
Crimping Machine 卖方: Hangzhou Zhongyuan Machinery Factory Crimping Machine Technical Data of Crimping Forming Machine Raw material corrugat...
Stud & Track Forming Machine
Stud & Track Forming Machine 卖方: Hangzhou Zhongyuan Machinery Factory Stud & Track Forming Machine Technical Data of Stud and Track Forming Machine Suitab...
Sigma Forming Machine
Sigma Forming Machine 卖方: Hangzhou Zhongyuan Machinery Factory Sigma Forming Machine Technical Data of Sigma Forming Machine Suitable Material Cold-r...
Cable Tray Forming Machine
Cable Tray Forming Machine 卖方: Hangzhou Zhongyuan Machinery Factory Cable Tray Forming Machine Technical Data of Cable Tray Forming Machine Suitable raw material...
Guardrail Roll Forming Machine
Guardrail Roll Forming Machine 卖方: Hangzhou Zhongyuan Machinery Factory Guardrail Roll Forming Machine Technical Data of Guardrail Roll Forming Machi...