Puncture Strength Tester
Introduction to the Device This device is a testing machine used to measure the "puncture strength" when a sample is penetrated by a test needle. As a physical test for battery separators, it can measure the breaking strength of the force applied in the vertical direction. It can be used for evaluating the strength of the separators (isolation membranes) inside lithium - ion batteries and testing the puncture strength of packaging materials such as food packaging films. Features This tester can only measure the puncture strength when the sample is pierced by a needle. The breaking strength under the force in the vertical direction is one of the physical test methods for battery separators, which can be measured by this tester. Technical Requirements 1. **Measurement environment temperature and humidity**: Temperature 20～30°C, humidity 50～70%RH without condensation (Standard temperature and humidity conditions: Temperature 20°C, humidity 65%RH) 2. **Load detection** - Detector: Differential transformer (ring - type dynamometer) - Load (full - scale range): Four - range switching of 100gf, 200gf, 500gf, and 1000gf - Accuracy: Within ±0.5% of the full - scale range 3. **Displacement detection** - Detector: Potentiometer - Maximum displacement: ±0.5mm - Accuracy: Within ±0.5% of the full - scale range 4. **Special test needle tip**: Designed with consideration for the testing of separators, with a diameter of 1mm and a tip shape of 0.5R 5. **Diameter of the middle through - hole of the sample fixing plate**: 10mm 6. **Displacement speed** - Standard measurement: 0.02(mm/sec) <1mm/50sec> - High - sensitivity measurement: 0.0067(mm/sec) <1mm/150sec>. Other settings can also be made as required. 7. **Measurement modes**: Load control mode and displacement control mode. The above two modes can be switched. 8. **Sample size (standard)**: 15mm×15mm or larger, with a thickness of 1mm or less.
在线联系供应商
Other supplier products
 |
Glow wire tester - Test Equipment | F242 Glow-wire tester, By simulating the thermal stress caused by heat source or ignition source such as hot component or overload resistor in a sh... |
 |
Taber Abrasion Tester (Double-Head) - lab instrument | We are a professional testing instrument manufacturer offering complete laboratory testing solutions. If you need more information or wish to explo... |
 |
Luminous Afterglow Performance Tester - Test Equipment | The luminous afterglow performance tester is suitable for testing the luminous afterglow performance of various textiles. Fibers, yarns, and powder... |
 |
Rubber non-rotor vulcanization Tester | The Rubber Non-Rotor Vulcanization Tester is a precision instrument designed for the rubber processing industry to monitor and control rubber mater... |
 |
Geotextile thickness meter | Instructions: 1. in the carpet test, in order to test the thickness and compression recovery, the instrument can provide a presser foot and a set ... |
Same products
 |
Hydraulic Oil Filtration and Dehydration Unit | 卖方: Standard Groups | The Hydraulic Oil Filtration and Dehydration Unit is an integrated oil purification system that c... |
 |
Hydraulic Pump Contamination Resistance Tester | 卖方: Standard Groups | The Hydraulic Pump Contamination Resistance Tester is primarily used to test the fuel pump's resi... |
 |
Filter cartridge pore size tester | 卖方: Standard Groups | This instrument is widely used in fields such as determining the effective pore size of geotextil... |
 |
Filter Dynamic Cycling Tester | 卖方: Standard Groups | Filter element dynamic cycling test bench is mainly used to test the chemical element precipitati... |
 |
Steam Jet Test Chamber，anti-corrosion steam spray testing chamber | 卖方: Standard International Group (HK) Limited | The Steam Jet Test Chamber is designed to evaluate the durability and performance of materials an... |
