Pressure Relief Valve
This valve is opened to prevent the pipeline and equipment from being damaged due to overpressure when the pressure in the water supply pipeline exceeds the set pressure of pressure relief. The valve closes automatically when pressure drops to the set value.
Festures of cold water pressure relief valve
Accurate Pressure Control
Fast Opening to Maintain Line Pressure
Slow Closing to Prevents Surges
Completely Automatic Operation
Inlet pressure water enters the lower cavity of the pilot valve diaphragm from the guide valve when the pressure in the pipeline exceeds the set pressure of the guide valve to make its pressure increase to open the guide valve, the main valve control room outwards drain under the effect of the inlet pressure water to open the main valve, it starts to discharge pressure. When the pressure in the pipeline drops to the set pressure, the pressure in the lower cavity of the guide valve diaphragm decreases, causing the guide valve closed. This results in increased water pressure from the guide pipe to the pilot valve, then to the main valve control room. The main valve plate closes and begins to hold pressure.
Pressure Relief Valve Installation and Commissioning
The pressure relief(sustaining) valve supports horizontal and vertical installation but should pay attention to the inlet and outlet direction of valve body water when installing. In general, one fire water supply system can only install one pressure relief valve. Within the operating pressure range of the spring specified in the nameplate, the opening pressure can be adjusted by rotating the adjusting screw to change the spring compression amount. For specific use, please consult ZECO Valve and Gate Group.
Pressure Relief Valve Material and Standard
Size Range: 2"~24"
Pressure Rating: 10bar ~ 25bar
Face to Face Dimensions: AMSE B16.10, EN558-1
Flange End Dimension: AMSE B16.1/16.42, AS4087, EN1092-2
Coating: Fusion Bonded Epoxy Coating
Inspection and Test: ISO 5208 / EN 12226-2
|
Part |
Material |
Standard |
|
Body |
Ductile Iron |
EN 1563/DIN 1693 |
|
Bonnet |
Ductile Iron |
EN 1563/DIN 1693 |
|
Trim |
Stainless Steel 431 |
EN10088-1/ASTM A959 |
|
Seat |
Stainless Steel 431 |
EN10088-1/ASTM A959 |
|
Diaphragm |
EPDM / NBR |
ISO 4633 |
|
Pilot Valve |
Stainless Steel 431 |
EN10088-1/ASTM A959 |
|
For the materials options not listed, consult factory. ZECO manufactures valves in more than 50 different alloys. |
||
As one of pressure relief valve suppliersand pressure relief valve manufacturers, we can offer kinds of related products for sale, if you want to buy pressure relief valve, please contact us.
If you want to know more kinds of check valve, please visit our website.
在线联系供应商
Other supplier products
 |
3 Inch Ball Valve | Description of 3 inch stainless steel ball valve: ZECO3 inch ball valveis usually a floating ball valve, the material can also be divided into cast... |
 |
Backflow Preventers | Basic informationThis valve is installed at the outlet of the water pump. It can prevent the backflow of the medium, linked with the water pump, an... |
 |
Bronze Adjustable Dynamic Flow Balancing Valve | ZECO is one of the leading check valve manufacturers china, China. ZECO check valveprovides non-slam closure, have a low head loss and close drip-t... |
 |
Wedge Gate Valve | Description Wedge gate valve is a linear motion, multi-turn general service valve. Table of Contents Gate valve Types as per Type of Closing E... |
 |
Resilient Seated Gate Valve | Features of resilient seal gate valve Full diameter flat - bottom runner, no debris pooling; Fully covered EPDM disc, no corrosion; Movabl... |
Same products
 |
Check Valve, 600 LB, 1/2 Inch, Piston type, Bolted Cap | 卖方: China Valmax Valve Co., Ltd. | China Check Valve manufacturer Valmax supplies Check Valves with the body, bonnet, disc, and se... |
 |
Check Valve, 900 LB, 1/2 Inch, RF, Pressure Seal Cap | 卖方: China Valmax Valve Co., Ltd. | China Check Valve manufacturer Valmax supplies Check Valves with the body, bonnet, disc, and se... |
 |
Check Valve, 600 LB, 1/2 Inch, Piston type, Bolted Cap | 卖方: China Valmax Valve Co., Ltd. | China Check Valve manufacturer Valmax supplies high-quality Check Valves, with the body, bonnet... |
 |
Combination angle valve | 卖方: Zhejiang Huaqi Information Technology Co., LTD | Meet our Brass Angle Ball Valve, a versatile and reliable solution for controlling fluid flow in ... |
 |
Multifunctional hydraulic control valve | 卖方: FLUID TECH PIPING SYSTEMS (TIANJIN) CO.,LTD | Features: Size: 2"-24”(DN50-DN600) Material: Ductile iron ASTM A536, 65-45-12 Dimension:... |
