.

KES - FB2 - S Bending Tester

Compliance Standards

ASTM D790 (Plastics Flexural Properties)

ISO 178 (Flexural Strength of Rigid Plastics)

SAE J2748 (Automotive Composite Flexure)

IEC 62133-2 (Battery Module Bending)

EN 1170-5 (GRC Flexural Testing)

Technical Parameters

ParameterSpecification
Force Range 0.1N - 2000N (±0.5%)
Deflection Accuracy ±1μm @ 10mm span
Test Speed 0.1 - 500 mm/min
Support Spans 10-500mm (adjustable)
Bending Radius 0.5-100mm (±0.01mm)
Angular Resolution 0.01°

Key Features

3-point & 4-point bending configurations

Real-time curvature measurement system

Automatic neutral axis calculation

High-speed strain mapping (1000 fps)

Multi-stage bend/reverse bend cycles

Test Capabilities

Test TypeStandardParameters
Flexural Modulus ASTM D790 2% strain limit
Bending Fatigue ISO 12106 10⁷ cycles @ 20Hz
Springback Analysis SAE J2748 180° bend + release

Measurement System

  • Dual-axis load cell (Fz + Mx)
  • Laser-based deflection tracking
  • Surface strain mapping via DIC
  • Real-time moment-curvature plots

Standard Configuration

  • Stiffness-rated frame (100kN/m)
  • Interchangeable rollers (R1-R50mm)
  • TestXpert III analysis software
  • 2000N capacity load cell

Automotive Options

  • Battery pack torsion simulation
  • Seat structure cyclic loading
  • Door seal compression-bend
  • Thermal cycling (-40°C to 150°C)

Safety Systems

  • Over-moment protection
  • Emergency roller retraction
  • Specimen ejection detection
  • Automatic force dump circuit

Implementation Notes

  • Calibrate per ISO 5893 (Roller alignment)
  • Maintain 40-60% RH for polymer tests
  • Use alignment jig for multi-layer stacks
  • Ground isolation for electronic components

Implementation Notes

  • Calibrate per ISO 5893 (Roller alignment)
  • Maintain 40-60% RH for polymer tests
  • Use alignment jig for multi-layer stacks
  • Ground isolation for electronic components

在线联系供应商

至: 标准集团
Your E-mail:
消息正文:


Send to other suppliers

Other supplier products

BBA steady state solar simulator tester
BBA steady state solar simulator tester Standard IEC 61215: Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval IEC 61646: Thin-Film Terrestrial Photo...
Paper folding tester
Paper folding tester Paper folding tester - Other test instrument - standard Product Information: Test principle The machine uses the motor drive screw to move the f...
Mask combustion tester
Mask combustion tester Standards: GB 19083-2010, EN 149, GB 2626, YY 0469 Applications: Mask combustion tester is to determine the fire resistance performance of...
Sharp Tip Tester
Sharp Tip Tester Meet the standard: ASTM F963 EN 71-1 ISO 8124-1 Product Introduction: Certain points on toys, if excessively sharp, can cause injuries. Safe...
Total Hip Joint Prostheses Wear Tester
Total Hip Joint Prostheses Wear Tester Standard YY/T 0651.1-2016 (China): Specifies wear testing parameters for total hip prostheses, including angular motion, loading modes, and envi...
供应产品

Same products

PH-2398  pH/EC/ORP/温度 多参数测试仪
PH-2398 pH/EC/ORP/温度 多参数测试仪 卖方: 科立龙电子股份有限公司 大显示,可同时进行水质PH、氧化还原电位、电导率、温度的测量; 带背光LCD显示清晰,功能齐全,精度高; 仪表采用微电脑测量与控制技术,具有自动校准功能,方便实用。 内置蓝牙,可以与电脑或...
ORP-2026S  防水型 土壤ORP&温度 二合一测试仪
ORP-2026S 防水型 土壤ORP&温度 二合一测试仪 卖方: 科立龙电子股份有限公司 范围 ORP -999~999mV Temp 0~50℃ 分辨率 ORP 1mV...
防水型 EC /TDS/温度三合一参数测试仪
防水型 EC /TDS/温度三合一参数测试仪 卖方: 科立龙电子股份有限公司 范围 EC ~19.9mS TDS Temp 0~50℃ 分辨率 ...
EC-98330 电导率营养测试棒
EC-98330 电导率营养测试棒 卖方: 科立龙电子股份有限公司 本营养测试仪适用于水培和农业应用,能够准确测量水中的营养液电导率(EC)单位为mS/cm,以及总溶解固体(TDS)转换为百万分之一(ppm)。 适合需要较高EC值的植物,该测试仪具有高达6.0...
PH-808防水笔式土壤PH计
PH-808防水笔式土壤PH计 卖方: 科立龙电子股份有限公司 两点按键校准,自动识别pH标准缓冲液 自动温度补偿确保全量程范围的精确测量。 自动电源关闭,有效节省电池能耗。 可替换型电极降低仪表维护与使用成 全防水性能保障在恶劣环境中对仪表的完整保...