Safety Helmet Roll-off Testing Equipment
The safety helmet retention test equipment is a device used to evaluate the stability of a helmet's fit when subjected to impact. By simulating the pulling forces and impact scenarios of an accident, it accurately assesses the reliability of the helmet's retention system, providing a rigorous technical safeguard for the safety of cyclists. The equipment mainly consists of a simulated head form, a tensile loading system, an impact track, and a data acquisition system. During the test, the helmet is secured to the simulated head form according to standard wearing procedures, and the length of the helmet straps and the tightness of the buckles are adjusted to ensure a fit that matches actual wearing conditions.
Application
Apply an initial load of a certain force to the rear of the helmet. Then, let a weight specified by the standard fall from a certain height so that the impact force is also applied to the helmet. In this way, the wearing stability performance of the helmet can be evaluated.
Standard
IS 4151:Indian Standard for Protective Helmets
ECE R22.05:Uniform Provisions Concerning the Approval of Protective Helmets and Their Visors for Drivers and Passengers of Motor Cycles and Mopeds
Feature
Dynamic Tensile Testing: A tensile force is applied to the helmet using a tensile loading system, and the maximum tensile force is recorded to ensure the helmet does not detach during the test.
Impact Testing: The helmet is worn and slid down a track to impact a rigid obstacle at a specific speed, and whether the helmet detaches is recorded.
Data Acquisition: An accelerometer records the impact force on the headform, comprehensively evaluating the stability of the fastening system under dynamic impact.
Safety Protection: The equipment is equipped with a safety enclosure to prevent injury from flying helmet fragments during testing.
Parameters
| Item | Detail |
|---|---|
| Mass of initial load | 3 kg ± 0.1 kg |
| Mass of falling weight | 10 kg ± 0.01 kg |
| Lowering height | 0.5 meters ± 0.01 meters |
| Measuring method | manual |
| Electricity | 220V 50HZ |
| Test theory | vertical descent |
Accessoriess
Anthropomorphic headform
Strap clamp
Force sensor
Impact drive assembly
Data acquisition and analysis system
Protection and limiting devices, etc.
Test Procedures
1. previously to the ambient temperature and sanitary conditions for the conditions of the helmet, should be placed on the appropriate head shape and fixed in the appropriate head.
2. In the median vertical plane of the helmet, a device that guides and releases the fall with a total mass of 3 kg ± 0.1 kg is attached to the rear of the shell.
3. 10 kg ± 0.01 kg of falling mass is released and lowered from a height of 0.5 m ± 0.01 m. The guiding device should ensure that the impact velocity is not less than 95% of the theoretical velocity.
在线联系供应商
Other supplier products
 |
Catheter Sliding Performance Tester | Standards YY/T 1536 - 2017 GB/T, ASTM, etc. Main Uses The catheter sliding performance tester is a precision instrument specifically designed t... |
 |
Leather thickness tester | Product Introduction Leather thickness tester is a special high-precision instrument for leather thickness measurement, which can be widely used f... |
 |
Cabin Air Filter Test System（Gas Adsorption） | Application Evaluating gas adsorption and desorption performance of cabin air filter elements Research and development of new filter media and pe... |
 |
Spinal Internal Fixation System Component Testing Machine | Standard YY/T 0119-2014 (China): Specifies mechanical testing protocols for spinal fixation components, including screws, plates, rods, and connec... |
 |
Fuel Water Separation Efficiency Test Rig | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications The Fuel Water Separator Test Bench is designed to evaluate the water separat... |
Same products
 |
Full-Body Garment Stress Tester,FZ/T 70015 | 卖方: Standard International Group (HK) Limited | TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exe... |
 |
Industrial Dry Cleaning Machine,industrial garment steamer | 卖方: Standard International Group (HK) Limited | TheIndustrial Dry Cleaning and Energy-Saving Dryer Machinesare designed for high-performance, rel... |
 |
MST Medical Compression Stocking Tester,compression sock tester | 卖方: Standard International Group (HK) Limited | The MST Medical Compression Stocking Tester is a professional instrument designed to evaluate the... |
 |
MMT Liquid Water Separation Tester,MMT Liquid Water Analysis Tool | 卖方: Standard International Group (HK) Limited | Applications Textile Manufacturing:Testing waterproof fabrics for outdoor gear R&D:Developi... |
 |
Dental material color stability tester | 卖方: Standard International Group (HK) Limited | Application The applications of color stability testers for dental materials are mainly reflecte... |
