Metal Corrosivity Tester

The Metal Corrosivity Tester is used to determine the corrosivity of liquids and solids that may become liquid during transport. It conforms to the UN Recommendations on the Transport of Dangerous Goods – Manual of Tests and Criteria 37.4. Test Methods for Determining Corrosivity of Metals, and GB 19521.6-2004. Safety Specifications for Testing Hazardous Characteristics of Corrosive Dangerous Goods. The instrument consists of three parts: a display and control unit, a testing system, and a water supply system. It features automatic sample level detection, automatic condensate circulation, and automatic water replenishment for the constant temperature water bath. The testing system is equipped with two sets of testing devices, allowing simultaneous corrosion tests on two different types of samples. Operators can monitor the entire testing process via an LCD screen.

Applications

The metal corrosivity tester is designed and manufactured in line with the requirements stipulated in the national standard of the People's Republic of China, GB/T21621 Test Method for Metal Corrosivity of Dangerous Goods. It is applicable to the metal corrosivity testing of liquid substances or solid substances that may become liquid during transportation.

Standards

It conforms to the United Nations Recommendations on the Transport of Dangerous Goods - Manual of Tests and Criteria 33.2.1.4 Test N.1: Test Method for Flammable Solids; conforms to GB/T 21618-2008 "Dangerous Goods - Test Method for Burning Rate of Flammable Solids"; conforms to NY/T 1860.15-2010 "Guidelines for Determination of Physicochemical Properties of Pesticides - Part 15: Flammability of Solids"; conforms to GB 5085.4 "Identification Standards for Hazardous Waste - Flammability Identification" 4.2 Flammable Solid Test; conforms to GAT536 "Classification and Test Methods for Fire Hazards of Flammable and Explosive Hazardous Goods"; and conforms to national standards and industry standards that are equivalent or equivalent to the above standards.

Features

1. It adopts an embedded processor and Windows CE operating system.

2. With an 8 - inch liquid - crystal touch screen, it can display the test status in real - time.

3. It integrates two functions, "sieving experiment" and "combustion rate experiment", into one.

4. It is applicable to the detection of two types of sample materials: non - metallic powder and metallic powder.

5. It is equipped with a standard stacking mold and features a user - friendly shaking handle design.

6. Strictly in accordance with standard requirements, an ignition torch is used for the sieving experiment, eliminating the need for a gas cylinder and ensuring safety.

7. A nitrogen rod is used as the ignition source for the combustion rate experiment. The material has high stability, and the ignition source temperature detection device ensures that the ignition temperature reaches above 1000°C.

8. It uses full - automatic infrared flame detection technology, which can reliably detect open flames and smoldering phenomena, ensuring detection accuracy.

9. It has a fault - detection function and audible and visual alarm functions to ensure the safety of the experiment.

10. The experimental process is fully automated, requiring no manual intervention. It supports functions such as parameter setting, data storage, and report viewing.

Technical Parameters

Operating environment	(5~40)°C, <85%RH
Temperature control range	Room temperature ~ 80°C
Temperature control accuracy	±1°C
Temperature uniformity	±0.5°C
Timing range	(0~30)days
Timing display resolution	1min
Sample container volume	3000mL, effective volume 2000mL

Accessoriess

1. Core Working Components

Sample Testing Unit

8-well sample etching tank (suitable for multiple parallel tests): Used to load test liquid/molten solid samples and metal specimens;

Metal specimen fixing bracket: Adaptable to standard specimens (such as steel and aluminum) as required by GB/T 12621. ensuring stable immersion/contact with the sample.

Environmental Control Unit

Compressor - Refrigeration circulating water tank: Supports the condensation system, maintaining a stable test environment temperature;

High-precision temperature sensor (accuracy ±0.5℃): Real-time monitoring of the test tank temperature, matching the temperature control range of "room temperature to 100℃";

Heating module: Achieves temperature rise and constant temperature control for the test.

Control and Display Unit

Touchscreen display: Used for parameter setting (temperature, duration) and real-time display of test status;

Embedded control module: Supports automated instrument operation and data storage.

2. Auxiliary Accessories

Sample Processing: Standard metal test pieces (meeting GB/T 12621 material requirements), sample melting and heating device (for easily liquefied solid samples during transportation), pipettes/measuring cylinders (for quantitative liquid dispensing);

Calibration and Maintenance: Temperature calibration standard source, test piece grinding/cleaning tools (sandpaper, anhydrous ethanol, drying oven);

Data Recording: USB flash drive (for exporting test data/reports), test piece weighing balance (accuracy 0.1mg).

Test Procedures

Taking "Corrosion Testing of Metals in Dangerous Goods" as an example, the procedure is as follows:

1. Sample and Test Piece Preparation

Sample Processing:

Liquid Samples: Shake well before use;

Solid Samples Easily Liquefied During Transportation: Heat to a molten state (temperature control must be matched to sample characteristics).

Metal Test Piece Processing:

Take a standard test piece (e.g., steel/aluminum test piece specified in GB/T 12621), grind to remove the surface oxide layer, clean with anhydrous ethanol, and dry;

Accurately weigh the initial mass of the test piece (recorded as m₁), and record the test piece dimensions (calculate surface area).

2. Instrument Preparation

Connect to AC220V power supply, start the instrument, and complete the fault self-check via the touch screen;

Check whether the condensation system (compressor - refrigeration circulating water tank) is operating normally, and calibrate the temperature sensor (ensuring ±0.5℃ control accuracy);

Clean the 8-well sample corrosion tank to ensure no residual impurities.

3. Sample Loading and Parameter Setting

Fix the prepared sample piece onto the support, place it in the sample container, and add the sample to be tested (ensuring the sample piece is completely submerged/in full contact with the sample);

Place the sample container into the corresponding holes of the 8-well corrosion tank;

Set the parameters via the touchscreen: test temperature (e.g., 25℃ room temperature or standard specified temperature), test duration (e.g., the stress corrosion test duration required by GB/T 15970), and start the condensation system.

4. Starting the Test

After confirming the parameters are correct, start the instrument's automatic program;

During the test, monitor the temperature and sample status in real time via the touchscreen. If leakage, abnormal temperature, or other issues occur, the instrument will trigger an audible and visual alarm (which must be addressed promptly).

5. Post-Test Processing and Data Analysis

After the test, stop the instrument and remove the sample.

Clean the sample surface of any remaining sample with the specified solvent, dry it, and weigh it again (record as m₂).

Observe the corrosion state of the sample (e.g., pitting, cracking, surface discoloration, etc.), and calculate the corrosion rate based on the mass change (formula: corrosion rate = |m₁ - m₂| / (sample surface area × test duration)).

Determine the metal corrosivity level of the sample according to GB/T 12621. and export the test report using the instrument.

6. Instrument Cleanup

Empty the sample corrosion tank, clean it with pure water, and allow it to air dry.

Turn off the instrument power and disconnect the condenser water circuit.

Other supplier products

	Thermal - Cold Cycle Testing Machine	The Thermal-Cold Cycle Testing Machine is a professional equipment used for high and low-temperature reliability testing. It is primarily used in f...
	Floor Caster Wear Test meter	Meet the standard: GB/T 11982.2. GB/T 4085. BS/EN 425. ISO 4918-2009 ASTM D6962 BS EN 425-2002 BS EN 985-2001 ISO 10581-2011 ANSI-NALFA-LF...
	Helmet Wearing Height Testing Machine	Main Purposes Measure the wearing height of helmets to ensure the accuracy and safety of helmet - wearing positions. Standard EN 397 GB 2812 Ce...
	Residual Ethylene Oxide Gas Chromatography System	The Residual Ethylene Oxide Gas Chromatography System is a professional analytical instrument designed for the detection and quantification of resi...
	Battery impact tester丨Battery impact chamber	Product Description Battery Heavy Impact Tester is a device that can be applied to the safety testing of lithium-ion batteries and battery packs, ...

供应产品

Same products

	Gas Oxidizing Property Tester	卖方: Standard International Group (HK) Limited	Product Description Conforms to ISO 10156-2010 “Gases and Gas Mixtures Selection of Cylind...
	Battery Powder Compaction Density Measurement System	卖方: Standard International Group (HK) Limited	The Battery Powder Compaction Density Measurement System is a precision testing system designed...
	Battery Powder resistance tester	卖方: Standard International Group (HK) Limited	The Powder Resistivity Meter is a precision testing system designed to measure electrical resisti...
	KES-SESRU surface roughness/friction tester	卖方: Standard International Group (HK) Limited	TheRoughness/Friction Tester analyzes hand movements-particularly, strokes-performed by artisans ...
	Air Permeability Tester STD- F8	卖方: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...