Hydraulic press
Leading technical parameters:
Nominal press force: 100MN
Return force: 5000kN
Rated working medium pressure: 31.9MPa
The distance between mould and platen (open): 2700mm
Main gliding block stroke: 1500mm
Working table size: 2500mm x 2500mm
Quick down speed of main gliding block: 200mm/s
Press speed of main gliding block: 40mm/s
Return speed of gliding block: 200mm/s
The press height above ground: 16800mm
Working power: AC400V, +5/-10%, 50Hz
Total power: 4200kW
Machine description:
The equipment is combined pre-tightening frame structure. It is composed of body, oil cylinder, hydraulic system, electric control system and lubrication system.
Body
The body is composed of upper beam, gliding block, working table (lower beam), column, push-rods, locking nuts and others. The frame is formed by upper beam, working table, column through push-rods and locking nuts at a pre-tightening condition. The main oil cylinder and return cylinder is installed on the upper beam, the plunger of oil cylinder connects to the gliding block for driving gliding block to move at an up-and-down direction against the column which is as guiding.
The equipment has an excellent guiding system of gliding block for a best capacity of anti-eccentric loading. It is with heat-expansion X type guide rail.
The limiting displacement of gliding block is considered in the design for preventing from breaking away from cylinder.
Upper beam
The upper beam is made of steel plate of steel grade Q235-A by welding in the protective gas of carbon dioxide, it is aging treated and stress-relief treated after welding. Main oil cylinder and return oil cylinder is installed on the upper beam. The filling tank is installed on the top of upper beam.
在线联系供应商
Other supplier products
 |
Ring rolling machine | D53 series 4000 5000 7000 Ring size OD (mm) 500-4000 500-5000 800-7000 Height (mm) 80-700 80-750 80-800 Machine parameter Radial rolling force (... |
 |
液压自由锻压机 | 5,000 TON HEAVY 4-COLUMN PUSH-DOWN HYDRAULIC OPEN DIE FORGING PRESS WITH 80 TON FORGING MANIPULATOR PRESS SPECIFICATIONS PRESS FORCE: 400.0 BAR (... |
|
|
Hydraulic press | Leading technical parameters: Nominal press force: 100MN Return force: 5000kN Rated working medium pressure: 31.9MPa The distance between mould... |
 |
Close die forging press | Max. press force: 30,000ton Leading parameter (1) Nominal press force: ≥70MN (2) Return force: ≥5MN (3) Moveable beam working speed Qui... |
 |
Rail bound forging manipulator | MANIPULATOR SPECIFICATIONS CARRYING CAPACITY, NOMINAL: 80 TONS TONGS CLAMPING MOMENT: 2,000 KNM TONGS OPENINGS, WITHOUT INSERTS, ROUND: 800/2,00... |
Same products
 |
SHJ Series Twin Screw Extruder | 卖方: Nanjing ChNanjing Chuanqi intelligent Equipment Co., Ltd.uanqi intelligent Equipment Co., Ltd. | The SHJ Series Twin Screw Extruder() represents a remarkable evolutionary step in the field of ex... |
 |
Underwater Pelletizer | 卖方: Nanjing ChNanjing Chuanqi intelligent Equipment Co., Ltd.uanqi intelligent Equipment Co., Ltd. | The Underwater Pelletizer(), a technological marvel in the polymer processing sector, has redefin... |
 |
Button sewing machine JM-373 | 卖方: Zhejiang Huaqi Information Technology Co., LTD | FeaturesIt is mainly used for sewing flat buttons with two holes or four holes. If attached, it c... |
 |
YZH固定式碎石机械臂系统 | 卖方: 山东伊润基础工程有限公司 | 对于固定应用，我们提供高级电源模块。该装置配备有电动机、液压泵和内置过滤器的油箱。对于我们的机器，我们提供手动和远程转向系统。标准设备的特点是手动转向，比例阀通常安装在固定式液压机械手的底座上。... |
 |
铸造锡基轴承合金 | 卖方: 河南桦创金属材料贸易有限公司 | 铸造锡基轴承合金 铸造轴承合金分为锡基、铅基轴承合金。虽然选用于滑动轴承轴瓦（轴套）的轴承材料有粉末冶金、非金属材料和金属材料等，但工业中常选用的还是非铁金属的铸造轴承合金，习惯称为铸造轴承合金... |
