Shoe Sole Heat Resistance Tester / Shoe Materials Heat Resistance Tester
Reference standard
EN ISO 20344. EN ISO 8772-1. GB/T 20991-2007. ANSI, JIS, CSA, GB12017-1989. LD50-1994 and other standards
Main uses
The sole heat resistance tester is used to test the heat resistance and temperature insulation performance of finished shoes under high temperature sand and stone heat temperature medium.
Product Features
Heated sand bath with specific dimensions and minimum sand height.
Heating system capable of heating the sand to controlled test temperatures (150℃ or 250℃).
Temperature control system to maintain the sand bath at the specified test temperature with a certain tolerance.
System for accurately measuring and recording the temperature change on the upper surface of the insole over a specified time (30 minutes), using a copper/copper-nickel thermocouple with a copper disc.
Uses sand of a specific particle size range and volume as the primary heat transfer medium.
May include provisions for using other heat transfer media, such as 5mm steel balls, depending on the specific test standard or configuration.
Fixture or area for placing the finished shoe on the heated sand bath, ensuring good contact.
Robust construction suitable for operating at high temperatures.
Test principle
The sandbox is heated to 150℃， the sand covers the contact point between the sample upper and the sole, and the change of the insole temperature over 30 minutes is recorded, accurate to 0.5℃。
Technical parameters
Sand bath box size: (40±2)cm*(40±2)cm, height: 8cm
Sand height: ≥5cm
Sand size: (0.3 —— 1.0)mm
Sand volume: 5000±250cm
Test temperature: (150±5)℃ or (250±5)℃
Heating power: 2500±250W or more
Heat transfer medium: 5mm steel ball, total mass 4kg
Copper/copper-nickel thermocouple: Solder a copper disc 2±0.1mm thick and 15±1mm diame
在线联系供应商
Other supplier products
 |
Qinsun Xenotest 220 | Standards ISO 105-B02: Lightfastness testing for colored textiles. AATCC TM16 (Option 3): Accelerated weathering for textiles under controlle... |
 |
Elastic Tape Fatigue Testing Machine / Elastic Fatigue Testing Machine | Product Introduction: This instrument is used to test the elasticity of elastic belt after reciprocating movement. Standards: SATRA TM103 Appli... |
 |
Plastic Pipe Hydrostatic Pressure Burst Tester | Standard ISO 1167: For thermoplastics pipe systems under constant internal pressure. ASTM D 1598: Standard test method for time-to-failure of pla... |
 |
Safety Helmet Electrical Insulation Tester GB/T2811 | Product Introduction: Safety hat electrical insulation performance tester used to test the electrical insulation performance of safety hat, high d... |
 |
Xenon Test Chamber/weather ometer | IntroductionWeather-Ometer and Fade-Ometer tester adopts water-cooled xenon lamp. This instrument using argon arc lamp simulation control ideal nat... |
Same products
 |
Bottle Wall and Bottom Thickness Tester | 卖方: Standard Group (Hong Kong) Limited | The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha... |
 |
Pinhole Tester / Pinhole Testing Equipment | 卖方: Standard Group (Hong Kong) Limited | The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ... |
 |
Cork Puncture and Chip Detection Instrument | 卖方: Standard Group (Hong Kong) Limited | The rubber stopper puncture debris detector is a device specifically used to detect the number of... |
 |
Aluminum Ointment Tube Toughness Tester | 卖方: Standard Group (Hong Kong) Limited | The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind... |
 |
Vacuum leak tester / Vacuum leak instrument | 卖方: Standard Group (Hong Kong) Limited | Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott... |
