Computer controlled memory impact testing machine

Product Introduction:

Computer controlled memory impact testing machine is mainly used for hard plastics, reinforced nylon, glass steel, ceramics, cast stone, electrical insulation materials and other non-metallic materials impact toughness determination. The testing machine is an ideal test equipment for chemical industry, scientific research units, colleges and universities, quality testing departments, professional manufacturers laboratories and other units. It is a testing instrument with simple structure, convenient operation and accurate and reliable data.

Meet the criteria:

1.JB/T 8762-1998 "Plastic Simply supported beam Impact Testing Machine"

2.JJG145-2007 "Verification Regulations of Pendulum Impact Testing Machine"

3.GB3808 "Test of pendulum impact Testing Machine"

Applicable standards:

1.GB/T 1043.1-2008 "Rigid plastic simple support beam impact test method"

2.ISO 179-1993(E) "Plastics - Determination of impact strength of simply supported beams"

Technical indicators:

1. Impact energy: 2J/4J(simply supported beam); 2.75/5.5J(cantilever)

2. Sampling rate: 10us

3. Resolution: 16 bits

4. Load measurement accuracy: ≤1%

5. Impact knife Angle: 30°

6. Pendulum torque: simple beam 2.1436N.m, 1.0718N.m, 0.5359N.m

7. Cantilever beam 2.9474N.m, 1.4737N.m

8. Pendulum prelift Angle: 150°

9. Simple support beam:

1) Impact speed: 2.9m/s

2) The distance from the center of the pendulum shaft to the center of the sample: 230mm

3) Blade Angle: 30°

4) Blade radius: 2mm

5) Support corner radius: 1mm

6) Front Angle of support: 5°

7) Rear Angle of support: 10°

8) Support span: 40. 60. 70mm

9) Sample type and size (length × width × thickness)mm3:80×10×4mm, 50×6×4mm, 120×15×10mm

10. Cantilever beam:

1) Impact speed: 3.5m/s

2) The distance from the center of the pendulum axis to the center of the sample: 335mm

3) Blade Angle: 75°

4) Blade radius: 0.8mm

5) Front edge Angle: 5°

6) Blade back Angle: 10°

7) Sample type and size (length × width × thickness)mm3:

80×10×4mm

63.5 * 12.7 * 12.7 mm

63.5 * 12.7 * 6.4 mm

63.5 * 12.7 * 3.2 mm

Other supplier products

	Sample machine / Sample Testing Machine	Purpose: The products are suitable for all kinds of textiles, leather, nonwovens and other products in the inspection of samples. Wide application...
	Shoe Bending Stiffness Tester / Shoe Outsole Bending Stiffness Tester	Applications: Shoes Bending Stiffness Tester is used to measure bending resistance of whole shoes (France shoe Size 39. 42.and British shoe Size 6...
	Qinsun UV-master	In response to the climate resistance testing requirements for outdoor textiles, this equipment can simulate outdoor climate conditions and accel...
	Thermal - Cold Cycle Testing Machine / Hot and Cold Thermal Cycling Testers	Standard BS 7291: Compliant for thermal cycling tests on thermoplastic pipe systems (1769 Series with pressure chamber). Adaptive Certification: ...
	Scott Flex Tester JIS L1096	Product Introduction: Scott kneading tester is suitable for back and forth kneading resistance of leather, leather and woven materials. One end o...

供应产品

Same products

	Bottle Wall and Bottom Thickness Tester	卖方: Standard Group (Hong Kong) Limited	The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha...
	Pinhole Tester / Pinhole Testing Equipment	卖方: Standard Group (Hong Kong) Limited	The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ...
	Cork Puncture and Chip Detection Instrument	卖方: Standard Group (Hong Kong) Limited	The rubber stopper puncture debris detector is a device specifically used to detect the number of...
	Aluminum Ointment Tube Toughness Tester	卖方: Standard Group (Hong Kong) Limited	The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind...
	Vacuum leak tester / Vacuum leak instrument	卖方: Standard Group (Hong Kong) Limited	Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott...