Precision Fiber Microtome ISO 137 IWSTM 24
Standards:
ASTM D2130. BS 2043. DIN 53811. ISO 137. IWSTM 24. IWTO 8-6
Applications:
Precision Fiber Microtome is used to produce accurate cross-sectional specimens of fibre for further examination under a microscope. Fiber cross sections of varying thickness from 10 microns are produced for microscopic examination, measurement and identification.
Product Information:
A degreased bundle of fibre is inserted into the slot on the top of the Microtome. An embedding
medium is applied to the bundle and allowed to dry. The fibre bundle is placed on the ejector and the micrometer wheel is used to determine the required parameters of the precision cut.
Cross-sectioning reveals certain characteristics that may be used to identify fibres, including:
1.Contour of the fibre
2.Thickness of the cuticle layer
3.Presence of medulla – if present, its type, shade, contour in relation to that of the fibre, and position in the fibre
4.Presence of pigment – if present, its distribution whether it is sparse, dense or in large aggregates, and whether it is most dense near the medulla or near the cuticle or arranged in bi-lateral form
5.Dye penetration
Operation Instructions of Precision Fiber Microtome:
1.Turn the micrometer wheel to the end.
2.Screw off the two screws on the cover, remove the cover.
3.Insert the fibre into the slot of the cover showing a small cut out.
4.Tighten the screws up, push the pushing plate to the side of the slot to compress the fibre, lock the nut on the plate.
5.Cut the fibre along the cover with the blade.
6.Turn the micrometer wheel until showing the required parameters.
7.Take drops of collodion on it.
8.Cut the fibre along the cover with the blade again.
Technical Parameters:
1.Weight: 3kg(6.6lb);
2.Outside dimensions: 75×150×100mm(L×W×H).
在线联系供应商
Other supplier products
 |
Geomembrane Fracture Resistance Tester | Standard ASTM D7176(Standard Test Method for Determining the Resistance of Geomembranes to Slow Steady-State Strain) ISO 17548(Geosynthetics - ... |
 |
Safety Helmets Wearing Stability Tester | Standard GB 811-2022: Safety Helmets – General Technical Requirements GB 24429-2009: Sports Helmets – Requirements and Test Methods... |
 |
Mask synthetic blood penetration tester | Standards: GB 19083-2010 Technical requirements of medical face masks - Anti-penetration property of 5.5 synthetic blood. YY/T 0691-2008 Clothin... |
 |
Automatic open flash point tester | Product Introduction: The instrument can automatically test the flash point and ignition point of petroleum products （the ignition point of oil ex... |
 |
Computer-controlled Helmet Impact Tester | Introduction： In a world where safety is paramount, especially for activities ranging from motorcycling and cycling to industrial work and extreme... |
Same products
 |
Plastic Smoke Density Tester F313 | 卖方: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... |
 |
Xenon Test Chamber | 卖方: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | 卖方: 上海千实精密仪器 | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | 卖方: 上海千实精密仪器 | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | 卖方: 上海千实精密仪器 | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
