Monel Steel
Monel Steel
bar （mm）8-300MM
Wire (mm) 0.2-8MM
Outer diameter of steel tube (mm) 3-426MM0.5-60 wall thickness
Strip (mm) thickness 0.05-5MM
Forging (mm) according to customer requirements
Flange (mm) according to customer requirements
Use of Monel Alloy:
The structure of the K500 Haomonnell alloy is a single phase solid solution with high strength. It is a kind of corrosion resistant alloy with the largest dosage, the most widely used and the best comprehensive performance. The alloy has excellent corrosion resistance in hydrofluoric acid and fluorine medium as well as excellent corrosion resistance to hot concentrated alkali solution. Also resistant to neutral solutions, water, seawater, atmosphere, organic compounds and so on. An important feature of the alloy is that it does not produce stress corrosion cracking and has good cutting performance. The alloy is mainly used for valve stem, pump shaft and impeller, conveyer scraper, well drilling ring, elastic parts, valve pad and so on.
Corrosion resistance of NCu30-2-1 Monel alloy steel K500 Monel alloy steel
The alloy has excellent corrosion resistance in fluorine gas, hydrochloric acid, sulfuric acid, hydrofluoric acid and their biota.
Acid medium: M400 is corrosion-resistant in sulphuric acid of less than 85% concentration. M400 is one of the few important materials in hydrofluoric acid.
Water corrosion: under most water corrosion conditions, M400 alloy not only has excellent corrosion resistance, but also the pitting corrosion and stress corrosion are seldom found, and the corrosion rate is less than 0.025mm/a.
High temperature corrosion: the maximum temperature of M400 working continuously in air is generally about 600 ℃, and in high temperature steam, the corrosion rate is less than 0.026 mm / a.
Ammonia: due to the high nickel content of Monel 400 alloy, it can resist corrosion under the condition of anhydrous ammonia and ammoniation below 585 ℃.
The corrosion resistance of Monel K500 in general solution state is basically the same as that of Monel 400 alloy. Therefore, the corrosion resistance data of Monel 400 can be applied to Monel K500 alloy. Because of its low corrosion rate in flowing seawater and high strength of the alloy, the alloy is especially suitable for the manufacture of centrifugal pump shafts resistant to seawater corrosion.
Matching welding material
Monel Monel400 electrode (ENiCu-7) Monel400 wire (ERNiCu-7)
Purpose:
Marine heat exchangers, desalination equipment, salt production equipment, marine and chemical processing equipment, propeller shafts and pumps, gasoline and water tanks, etc.
If you require further information or you do not see what yo need in our web,please do not hesitate to contact us. Our customer service specialists will be happy to help you.
contact us any
Other supplier products
|
|
Equal Tees Pipe Fittings |
Three links also known as pipe fittings or three-way pipe fittings, three-way joints, etc. Mainly used to change the direction of the fluid, used i... |
|
|
ASTM A210 Seamless Carbon Super Heater Tubes |
ASTM A210 Seamless Carbon Super Heater Tubes
Grade :A210A1、A210C
OD:12.7 to 127 mm
WT:0.9 to 12.7 mm
ASTM A210 is the standard covers... |
|
|
Concentric Reducer Pipe Fittings |
Product specification: 3 / 4 "X 1 / 2" -48 "X 40" [DN 20 X 15-1200 X 1000]
Wall thickness size: Sch. 5s 160
Standard: GB/T12459-2005, (ANIS),... |
|
|
90°Bends Pipe Fittings |
Product Details
90 ° Bends
OD:1 / 2 "-48"
WT:SCH20,STD,SCH40,SCH80,SCH160,XXS
1) 90 °Bends Pipe Fittings bend, large bend, RX 2 D 3 D 5 D... |
|
|
3EP Coated Steel Tube |
3EP coated steel tube Generally used in municipal and major building water supply and drainage above, it is the outer wall coating high adhesion, i... |
供应产品
Same products
