Wyzenbeek or Oscillatory Abrasion Tester
Product introduction:
Wyzenbeek wear resistance tester, also known as Oscillatory wear resistance tester, is used to test the wear resistance of fabrics against standard friction media or metal mesh surface friction movement, especially suitable for automotive decoration and furniture textile product. Instrument regulations American standard. There are 4 friction heads and electronic counter to control the running cycle.
Features：
Easy to control due to the precision electronic digital counter.
The protective cover provides protection and thus more safety.
Four abrasion heads to test samples simultaneously, thus greater efficiency.
Complied Standards：
ASTM D3597. ASTM D4157. CFFA-1A, FED-STD-191/5304. GM2756M, LP-463KB-06-01. LP-463KC-04-01. SAE J 948. SAE J1530. Toyota TSL 5101G 3.9.4 etc...
Working principles：
Install the long strip of sample fabric on the front and rear clamps of the friction head, and apply a certain tension force. Install the friction medium on the arc-shaped friction table to make the sample contact the friction medium and apply a certain load On the sample. The friction table swings back and forth to rub the sample, and after a certain number of frictions, evaluate the change in the breaking strength of the sample
![]()
Standard configuration：
Main machine 1set
Imported rubber pad 8pcs/pack
Imported metal mesh 4pcs/pack
Imported standard abrasive No. 10 cotton canvas (60inches X 5yards)
Power cable 1pcs
Manual 1pcs
![]()
Technical parameter：
1. Modern ergonomic design.
2. The suction device connected to the auxiliary vacuum cleaner.
3. Sealed transmission ensures quiet operation.
4. Test position: 4 heads.
5. Friction table: Curve surface-R100mm, length-400mm
6. Swing radian: 76+/-2mm.
7. Friction rate: 90+/-1/min(double friction).
8. Tension adjustment weight: 340g (tension adjustment range 8.9N-22.25N)
9. Load adjustment weight: 150g (load adjustment range 8.9N-17.8N)
10. Sample tension: 17.8N (adjustable)
11. Sample load: 13.4N (adjustable)
12. Sponge rubber pressure pad: 50X50mm(+/-1mm)
13. Instrument material: Stainless
14. Surface finishing: painting
15. Sample dimension: 245X73mm
16. Product dimension: 50X50X60 (LXWXH)
在线联系供应商
Other supplier products
 |
Temperature and Humidity Alternating Test Chamber for Automotive Wires-QINSUN | The temperature and humidity alternating test chamber for automotive wires conducts temperature and humidity alternating tests on automotive wire... |
 |
25 liters barrel washer machine | 25 liters barrel washer machine Model barrel washer Pressure 2-3bar Mains 220V or 380V Material Stainless steel, plastic ... |
 |
MARK-II Slip Resistance Tester | Product Introduction: Paste the cut sample on the test fixture of the portable MARK-II anti-slip testing machine, put down the weight of the rotat... |
 |
Car seat headrest static strength tester | Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test methods" : This standard specifies the static strength... |
 |
Santary tank cleaning nozzle | Application: STD ZG4 rotary tank washer is suitable for 3D cleaning of small to medium sized tanks,vessel or machines. It is commonly used in phar... |
Same products
 |
Seat Bumping and Creep Test Bench | 卖方: Standard International Group (HK) Limited | This test bench is used for simulating the car seat bumping and creep situation when a car is run... |
 |
Automobile seat belt fixed point test bench | 卖方: Standard International Group (HK) Limited | Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtur... |
 |
Impact strength tester for car seat headrest | 卖方: Standard International Group (HK) Limited | Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requi... |
 |
Impact strength tester for car seat launching headrest | 卖方: Standard International Group (HK) Limited | Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, w... |
 |
Automobile Headrest Strength Tester | 卖方: Standard International Group (HK) Limited | Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test me... |
