Filter Media Tester CIF 1000
CIF 1000 test rig for standard tests on motor vehicle passenger compartment filters in accordance with DIN 71460 part 1 and ISO/TS 11155-1 .
Palas®offers the CIF 1000 test rig with the Promo®1000 unit for standard tests on motor vehicle passenger compartment filters in accordance with DIN 71460 part 1 and ISO/TS 11155-1.
The volume flow is automatically regulated and adjustable from 60 to 800 m3/h. With the aid of the CIF, both the fraction separation efficiency and the burden on the complete filters or filter media are measured and evaluated.Particle dosing for the filter test is performed with the brush generator RBG 1000, which has been internationally established for over 30 years. On the CIF 1000, overall and fraction separation efficiency are determined with the high-resolution light scattering spectrometer Promo®1000.This allows reliable tests to determine the separation efficiency and burden tests to be performed across the entire measurement range for all particle sizes.The advantage of the Promo®1000 is the larger measurement range for particles from 120 nm. Following ISO/TS 11155-1, the test rig is additionally equipped with the salt aerosol generator AGK 2000. In the testing conduit, filter media up to a size of approx. 220 x 500 mm can also be tested under the conditions stated above. In order to test the influence of real ambient conditions on the separation behavior of filters, Palas®offers an upgrade to the CIF test rig with climate technology components foradjustment of the temperature between +18°C and +90°C and the relative humidity between 30% and 70%. As an option, the test rig can be upgraded after provision of the measuring equipment for gas analysis for investigations of the adsorption and desorption dynamics following DIN 71460 part 2 and ISO/TS 11155 part 2.
The CIF is equipped with ahigh-pressure ventilator, which can be throttled on the pressure side with infinitely variable adjustment and is frequency-controlled, and which can be automatically regulated via the FTControl filter test software for regulation of the volume flow. Furthermore, sensor data such as the volume flow, temperature, relative humidity and differential pressure at the filter are also recorded automatically during the filter test. The aerosol generators and the corona discharge can be actuated via the FTControl software.
Measurement of the fraction separation efficiency
Descriptions
Clear demonstration of the separation efficiency of your filters or filter media throughout the entire measurement range from 120 nm to 40 µm with the Promo®1000 system
Highest measurement reproducibility and repeatability highlight even fine differences in the separation efficiency
Short measurement times of around 2 minutes per separation efficiency measurement thanks to optimized application
Simple comparison of separation efficiency curves, calculation of mean values also possible Burden / hold time measurement and record of the pressure loss curve
Measurement point switching device
Benefits
Particle measurements from 120 nm
Measurement and evaluation of fraction separation efficiency and burden
Automatic data acquisition for barometer pressure, temperature, humidity, differential pressure
Temperature control (+18°C to +90°C) and moisture control (30 – 70%)
Automatic actuation of all test rig components
Automatic performance of the measurement processes
Individual programming of measurement processes for filter testing using the FTControl software
Separate measurement and analysis parts – this saves time and money, as the analysis can be performed while the measurement is still on-going
Printouts and saving of complete test records
Easy access to all data for the recorded measurement signals from the up to 6 external sensors
Low-maintenance
Easy operation
Reliable operation
The unit will reduce your operating costs
Other supplier products
|
PFE测试仪 |
医用口罩颗粒防护测试仪技术特点:配备了特殊的盐雾发生器,可以产生特定粒径和浓度的雾剂。自动控制气雾生成并自动计算捕集效率并掩盖气流阻力,从而减少了人为干预。配备了一系列专用夹具,适合检测各种口罩。内置高寿命光度计模块,累计采样时间,及时清洁光路。内置高精度电子流量计和高性能采样泵,确保流量稳定... |
|
Wyzenbeek Abrasion Tester |
Wyzenbeek Abrasion Tester
Testing Standards: ASTM D4157
Applications:
Wyzenbeek Abrasion Testeris used to determine the abrasion resistance of f... |
|
ultraviolet light accelerated weathering tester |
This product uses fluorescent UV lamps, combined with temperature and humidity device to simulate the material decline in color, brightness, streng... |
|
din abrasion resistance tester for rubber |
Din Abrasion Tester is designed to determine abrasion resistance index of natural and synthetic rubber in accordance with the above principle. It c... |
|
Taber Linear Abraser |
TheTABER Linear Abraser (Abrader) - Model 5750has been engineered to evaluate product’s abrasion resistance, scratch resistance (single or mu... |
供应产品
Same products