Rubber hose outer coating wear testing machine 丨 Rubber Hose Abrasion Tester
Product Introduction:
Rubber hose outer coating Wear testing machine for hydraulic hoses and other similar types of hoses with fabric or steel wire reinforced outer coating with a smooth and flat surface.
Test method:
1. Install the assembled sample and mandrel on the test device, and ensure that the sample has no axial movement and (or) rotation.
2. place the abrasive tool to make contact with the sample, apply the vertical static pressure F specified in the product standard, and start the machine. If the force F is not specified in the product standard, the applied vertical static pressure should be 50N±0.5N.
3. the test is carried out until the specified number of cycles is completed, and then the sample assembly is removed from the test device, and the sample with or without a core shaft is weighed again as the initial weighing. It is important to remove any particles attached to the outer coating before weighing.
Test standard:
GB/T 12721-2007 - Determination of abrasion resistance of rubber hose outer coating
ISO 6945:1991 - Determination of the abrasion resistance of rubber hose cladding
KS M ISO 6945-2013 - Determination of the abrasion resistance of the outer coating of rubber hoses
EN ISO 6945-1996 - Determination of the abrasion resistance of rubber hose outer coatings
DS/ISO 6945-1984 Determination of wear resistance of rubber hose cladding
Main parameters:
1. reciprocating frequency: 1.25Hz(45 RPM)
2. cycle stroke: 200mm
3. loading static pressure: 50N±0.5N(other pressure weights can be customized processing)
4. Mandrel length: 150mm
5. shaft diameter: 5mm, 8mm, 10mm, 13mm, 16mm, 19mm, 22mm, 25mm, 32mm, 38mm, 45mm, 51mm, optional three, can also provide dimensional processing
在线联系供应商
Other supplier products
 |
Hot Tack Tester / Heat Seal Tester | Standards GB/T 34445 - 2017 ASTM F2029 Main Uses The hot - tack tensile tester is an instrument specifically designed to test the hot - tacking ... |
 |
Heel Fatigue Tester ISO 19956 | Heel Fatigue Tester is used to determine the resistance of medium and high heels of ladies’ shoes under repeated small impacts to the heel ti... |
 |
Plastic Pipe Hydrostatic Pressure Burst Tester / Pipe Hydrostatic Pressure And Burst Tester | Standard ISO 1167: For thermoplastics pipe systems under constant internal pressure. ASTM D 1598: Standard test method for time-to-failure of pla... |
 |
Shoe Bending Stiffness Tester / Shoe Outsole Bending Stiffness Tester | Applications: Shoes Bending Stiffness Tester is used to measure bending resistance of whole shoes (France shoe Size 39. 42.and British shoe Size 6... |
 |
Guidewire Pushing Force Tester ASTM F | Standards YYT0807 - 2010 YY/T0663.2 - 2016 ASTMF2394 - 2007 Main Uses The guidewire pushing force tester is a precision testing tool in the med... |
Same products
 |
Briefly describe the importance, core functionality and how to implement a hospital clock system solution | 卖方: California Triangle | In the healthcare industry, precise time synchronization is critical. Every second can be a matte... |
 |
Sand and Dust Test Chamber for Automotive Connectors | 卖方: Standard International Group (HK) Limited | Operating Conditions: Ambient temperature: 5°C～+28°C (average temperature within 24 hour... |
 |
Automotive Connector SO₂/H₂S Corrosion Test Chamber | 卖方: Standard International Group (HK) Limited | Standards: GB/T 10587-89. GB/T 2423.9-93: Chinese national standards for sulfur dioxide corrosio... |
 |
Automotive Connectors Salt Spray Tester | 卖方: Standard International Group (HK) Limited | Applicable Standards: Neutral Salt Spray (NSS) Tests: GB/T2423.17. ISO 3768/3769/3770. ASTM B117... |
 |
Air - tightness Testing Device for Automotive Connectors | 卖方: Standard International Group (HK) Limited | Main Functions: 1. Provide stable positive and negative pressures for testing the air - tightnes... |
