Textile stress and strain tester for garments
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Applications
Full-Body Garment Stress Tester is used to evaluate the pressure exerted by various form-fitting garments or other wearable apparel on the human body. It quantifies the perceived pressure of clothing on the body into specific numerical data and enables assessment of test results. The manikin can perform both static and dynamic testing.
Dynamic postures meet the following requirements, considering the integrity of the form: the rear of the knees must not be left unprotected.
Standards
FZ/T 70015-2022 :Test Methods and Evaluation of Pressure in Knitted Compression Garments
Features
1.Accurate measurement of garment pressure at multiple body locations with high-resolution sensors.
2.Supports bothstaticanddynamic testing, simulating real-life movement and posture.
3.Pressure mapping allows objective evaluation of garment comfort and functionality.
4.Dynamic mannequin posture designed to maintain full body integrity, with clearance behind knees.
5.Enables design optimization for sports, medical, and fashion applications through data-driven analysis.
Parameters
| Item | Specifications |
|---|---|
| Pressure Mannequin | Average Asian female body type, height: 155 ~ 165 cm |
| Pressure Measurement Range | 0 ~ 90 mmHg |
| Test Accuracy | ≤0.1 mmHg |
| Resolution | ≤0.1 mmHg |
| Sensors | 26 independent sensors, each measuring a separate point. The sensor surface is flat and stable, with no mutual interference between measurement points. |
Test Procedures
I. Equipment Preparation and Calibration
Parameter Verification: Ensure equipment complies with FZ/T70015-2022 standards. The pressure manikin uses the average Asian female physique (height 155–165 cm).
Sensor Inspection: All 26 sensors must have flat surfaces and stable configurations to ensure independent measurements without interference.
Range Calibration: Pressure measurement range 0–90 mmHg, test accuracy ≤0.1 mmHg, resolution ≤0.1 mmHg.
II. Test Procedure
1. Static Testing:
Place the garment over the pressure manikin and adjust to the standard posture (void space behind knees).
Activate the equipment, record pressure values at each point, and analyze pressure distribution uniformity.
2. Dynamic Testing:
Simulate movement postures (e.g., running, jumping) and observe pressure changes.
Focus on pressure values in high-activity areas (e.g., armpits, waist).
III. Data Interpretation and Optimization
1. Comfort Assessment:
Excessive pressure (>90 mmHg) may cause constriction, while insufficient pressure fails to provide adequate support.
Optimize pressure distribution by adjusting fabric elasticity or cutting techniques.
2. Function Verification:
Performance compression garments must deliver moderate pressure to key muscle groups (e.g., thighs, calves) to reduce muscle vibration.
Medical garments must ensure uniform pressure distribution to prevent blood circulation obstruction.
在线联系供应商
Other supplier products
 |
Catheter Power Injection Flow and Pressure Tester | The Catheter Power Injection Flow and Pressure Tester is designed to evaluate the flow and pressure performance of catheters under high-speed and... |
 |
Helmets Xenon Lamp Aging Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards ISO 4892-2: Plastics—Methods of exposure to laboratory light sources&mdash... |
 |
Solid Split-Type Weighted Dummy | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications Solid Split-Type Weighted Dummies are widely used by automotive manufacturers... |
 |
Spinal Internal Fixation Components System Tester | Standard YY/T 0961-2014 (China): Specifies static/fatigue testing protocols for spinal fixation systems, including connection integrity and anti-l... |
 |
Resistance to flame propagation tester,ECE R118 Annex 10 | Introduction This equipment is designed and manufactured according to ECE R118 Annex 10. This model is intelligent, with PLC and touch screen in... |
Same products
 |
5750 taber linear abraser | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards ISO Standards: ISO 9352. ISO 5... |
 |
Custom textile rubbing color fastness tester | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards JIS L0849 — Test methods... |
 |
Textile Acid Printed Fabric Surface Wool Adhesion Meter | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards ISO 9073-4: Textile flatness m... |
 |
Textile Cool Feeling Tester | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications Fabric Cooling Sensation Te... |
 |
Textile far-infrared radiation temperature rise test instrument | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications Textile Far Infrared Radiat... |
