Textile stress and strain tester for garments

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Applications

Full-Body Garment Stress Tester is used to evaluate the pressure exerted by various form-fitting garments or other wearable apparel on the human body. It quantifies the perceived pressure of clothing on the body into specific numerical data and enables assessment of test results. The manikin can perform both static and dynamic testing.

Dynamic postures meet the following requirements, considering the integrity of the form: the rear of the knees must not be left unprotected.

Standards

FZ/T 70015-2022 :Test Methods and Evaluation of Pressure in Knitted Compression Garments

Features

1.Accurate measurement of garment pressure at multiple body locations with high-resolution sensors.

2.Supports bothstaticanddynamic testing, simulating real-life movement and posture.

3.Pressure mapping allows objective evaluation of garment comfort and functionality.

4.Dynamic mannequin posture designed to maintain full body integrity, with clearance behind knees.

5.Enables design optimization for sports, medical, and fashion applications through data-driven analysis.

Parameters

Item	Specifications
Pressure Mannequin	Average Asian female body type, height: 155 ~ 165 cm
Pressure Measurement Range	0 ~ 90 mmHg
Test Accuracy	≤0.1 mmHg
Resolution	≤0.1 mmHg
Sensors	26 independent sensors, each measuring a separate point. The sensor surface is flat and stable, with no mutual interference between measurement points.

Test Procedures

I. Equipment Preparation and Calibration

Parameter Verification: Ensure equipment complies with FZ/T70015-2022 standards. The pressure manikin uses the average Asian female physique (height 155–165 cm).

Sensor Inspection: All 26 sensors must have flat surfaces and stable configurations to ensure independent measurements without interference.

‌Range Calibration: Pressure measurement range 0–90 mmHg, test accuracy ≤0.1 mmHg, resolution ≤0.1 mmHg.

II. Test Procedure

‌1. Static Testing:

Place the garment over the pressure manikin and adjust to the standard posture (void space behind knees).

Activate the equipment, record pressure values at each point, and analyze pressure distribution uniformity.

2. Dynamic Testing:

Simulate movement postures (e.g., running, jumping) and observe pressure changes.

Focus on pressure values in high-activity areas (e.g., armpits, waist).

III. Data Interpretation and Optimization

1. Comfort Assessment:

Excessive pressure (>90 mmHg) may cause constriction, while insufficient pressure fails to provide adequate support.

Optimize pressure distribution by adjusting fabric elasticity or cutting techniques.

2. Function Verification:

Performance compression garments must deliver moderate pressure to key muscle groups (e.g., thighs, calves) to reduce muscle vibration.

Medical garments must ensure uniform pressure distribution to prevent blood circulation obstruction.

Other supplier products

	Pinhole Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The pinhole tester for aluminum foil is a device specifically used to detect micro - pinhol...
	Reciprocating Wear Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards ASTM F2496: Scratch hardness and adhesion testing for prints/coatings. ISO 1518...
	Medical injection needle rigidity tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application The tester is suitable for rigidity testing of medical injection needles in th...
	ISO 5660 Cone Calorimeter Fire Test Equipment Supplier Factory Direct	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Features Ignition System 10 kV spark igniter with fire-off safety system; p...
	Protective Clothing Chemical Liquid Penetration Resistance Tester EN 374 Chemical Protective Gloves Testing System	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Application You use this tester to measure the chemical liquid penetration r...

All supplier products

Same products

	Composite Flame Retardant For Adhesive XS-FR- 308/XS-FR-708	Seller: Zhejiang Xusen Flame Retardants Incorporated Company	XS-FR-308/XS-FR-708 are nitrogen phosphorus composite, low smoke intumescentflame retardants, whi...
	Nylon High Strength Sewing Thread	Seller: Hangzhou Fantex Textile Co., Ltd	Nylon high strength sewing thread(nylon thread) selects high toughness nylon filament as raw mate...
	HMPE Yarn	Seller: Hangzhou Fantex Textile Co., Ltd	Fantex high strength polyethylene yarn is a premium HMPE Yarn(High Modulus Polyethylene Yarn), re...
	Nylon Fishing Twine	Seller: Hangzhou Fantex Textile Co., Ltd	Our nylon fishing twineis made from high tenacity nylon twine , ensuring a long-lasting and relia...
	High Tenacity Polyester Bonded Thread	Seller: Hangzhou Fantex Textile Co., Ltd	High Tenacity Polyester Bonded Threadis a kind of industrial filament sewing thread made of high ...