Computer controlled memory impact testing machine

Product Introduction:

Computer controlled memory impact testing machine is mainly used for hard plastics, reinforced nylon, glass steel, ceramics, cast stone, electrical insulation materials and other non-metallic materials impact toughness determination. The testing machine is an ideal test equipment for chemical industry, scientific research units, colleges and universities, quality testing departments, professional manufacturers laboratories and other units. It is a testing instrument with simple structure, convenient operation and accurate and reliable data.

Meet the criteria:

1.JB/T 8762-1998 "Plastic Simply supported beam Impact Testing Machine"

2.JJG145-2007 "Verification Regulations of Pendulum Impact Testing Machine"

3.GB3808 "Test of pendulum impact Testing Machine"

Applicable standards:

1.GB/T 1043.1-2008 "Rigid plastic simple support beam impact test method"

2.ISO 179-1993（E） "Plastics - Determination of impact strength of simply supported beams"

Technical indicators:

1. Impact energy: 2J/4J（simply supported beam）; 2.75/5.5J（cantilever）

2. Sampling rate: 10us

3. Resolution: 16 bits

4. Load measurement accuracy: ≤1%

5. Impact knife Angle: 30°

6. Pendulum torque: simple beam 2.1436N.m, 1.0718N.m, 0.5359N.m

7. Cantilever beam 2.9474N.m, 1.4737N.m

8. Pendulum prelift Angle: 150°

9. Simple support beam:

1） Impact speed: 2.9m/s

2） The distance from the center of the pendulum shaft to the center of the sample: 230mm

3） Blade Angle: 30°

4） Blade radius: 2mm

5） Support corner radius: 1mm

6） Front Angle of support: 5°

7） Rear Angle of support: 10°

8） Support span: 40, 60, 70mm

9） Sample type and size （length × width × thickness）mm3:80×10×4mm, 50×6×4mm, 120×15×10mm

10. Cantilever beam:

1） Impact speed: 3.5m/s

2） The distance from the center of the pendulum axis to the center of the sample: 335mm

3） Blade Angle: 75°

4） Blade radius: 0.8mm

5） Front edge Angle: 5°

6） Blade back Angle: 10°

7） Sample type and size （length × width × thickness）mm3:

80×10×4mm

63.5 * 12.7 * 12.7 mm

63.5 * 12.7 * 6.4 mm

63.5 * 12.7 * 3.2 mm

Other supplier products

	Fabric ici pilling and snagging box-QINSUN	Standard GB/T 4802.3: China’s national standard for textile pilling resistance. BS EN ISO 12945-1: European standard for wool-based textile...
	Feeder	Peculiarity： Standard paint cup capacity ≤1L. Feeding design saves time and labor by eliminating back-and-forth pouring, enabling continuou...
	Car seat belt fixed point test bench	Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtures and headrests strength requirements and test me...
	Shoe Lace and Eyelet Abrasion Tester	Meet the standard SATRA TM93 DIN4843 QB/T 2226 SATRA TM 154 BS 5131:3.6:1991 ISO22774 Main uses The shoelace eye wear testing machine is ...
	Capillary rheometer	Standard: DIN 54811. ASTM D 3835. ISO 11443 Application: 1. It is suitable for measuring the shear rate of plastics and polymer materials and th...

All supplier products

Same products

	Sliding Bearing Fatigue Testing Machine	Seller: Standard Groups	The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua...
	Sliding bearing PV friction testing machine	Seller: Standard Groups	The sliding bearing PV friction testing machine is primarily used to evaluate the friction and we...
	High temperature vacum friction & wear tester	Seller: Standard Groups	High temperature vacuum friction and wear testing machine is mainly used to study the friction an...
	Dry Sand Rubber Wheel Wear Tester	Seller: Standard Groups	Dry and wet sand abrasive wear testing machine is mainly used to evaluate the wear resistance of ...
	Thrust Washer Friction Testing Machine	Seller: Standard Groups	The thrust washer friction testing machine is mainly used to simulate the frictional contact of m...