Hydraulic Oil Precision Filter Tester

1.Conformity standard:

GJB420. NAS1638. ISO4406. 18/16/13

2.Characteristics and Applications

2.1 Features of oil filter:

● Specialized gear pump set with low noise, strong self-priming ability and smooth operation.

● The high pressure pipeline is equipped with overflow protection device, which can effectively protect the safety of the hydraulic system.

● The coarse filter at the suction port protects the oil pump and extends the service life of the main filter.

● The fine filter can be selected with different precision according to the different needs of users to achieve the required results.

● The panel is equipped with a pressure gauge, which continuously indicates the operating condition of the system and the degree of contamination of the filter element during operation. There are differential pressure transmitters on the pre-filter and fine filter to indicate the system cartridge at any time.

2.2 Application of oil filtering machine:

Filtration of hydraulic lubrication system during refueling.

● Bypass filtration of hydraulic lubrication system during operation.

● Circulation filtration of hydraulic lubrication system before operation.

● Hydraulic lubrication system oil is not filtered and pumped out by the pump of the equipment itself.

(Note: This machine is not applicable to flammable and explosive media such as fuel oil.)

3. Technical Parameters:

Working Pressure: 0.6MPa

Differential Pressure for Alarm: 0.2MPa

Flow Rate: 50±5L/min

Medium: ≤160mm/s (20℃)

Accuracy: 5μm

Rated Power: 2.2KW

Power Supply Voltage: 3-phase 380V

Frequency: 50Hz

Operating temperature: 20 ℃ - 70 ℃

4. Cleaning and replacement of the filter:

When the oil filter works for a period of time, the oil filter oil system pressure increases accordingly, the performance of its components have different effects, especially on the filter precision of the filter element of the shadow

core damage, the main reason for this is that the filter element of the differential pressure rises, the need to replace the filter element. Specific cleaning and replacement methods are as follows:

4.1 Cleaning: (only on the pump before the suction oil filter)

4.1.1 Cleaning cycle: oil filter continuous work for a week (about 150 hours)

a. Unscrew the top cover of the oil suction filter and take out the filter element.

b.Cleaning the filter element:When cleaning the filter element, soak it with gasoline for about half an hour and then remove the impurities with a brush.

4.2 Replacement

4.2.1. Conditions for replacement: When the oil filter is filtering, when the red indicator pops up on the differential pressure alarm installed on the pre-filter and fine filter, the cartridge needs to be

4.2.2 Replacement method: loosen the four bolts on the upper cover of the pre-filter and fine filter, remove the upper cover, take out and replace the filter element.

5.Precautions

5.1 The oil filter can not filter gasoline and other flammable liquids.

5.2 If the oil pool (or tank) of the oil is too dirty and there may be large obstacles, in the suction port should be installed on the large mesh filter protection.

5.3 The oil suction and discharge pipes should be kept clean.

Other supplier products

	Digital Grinding Machine	Standard: GB/T 5211-16.GB/T 5211-19.GB/T 21867.1.GB/T 21868.5.ISO 787-16.ISO 787-17.ISO 8780-5.ISO 8780-1 I. Definition and Working Principle Di...
	Bally Waterproofness Tester	Applications: Bally Waterproofness Tester is to test materials like coated leather, leather dynamic water penetration resistance ability. The ma...
	Intervertebral Fusion Cages Torsion Fatigue Tester	Standard YY/T 0959-2014 (China): Specifies torsional fatigue testing protocols for intervertebral fusion devices, including load ratios, frequen...
	Dental Implants Fatigue Tester	Standard ISO 14801:2016: Specifies dynamic fatigue testing protocols for endosseous dental implants, including load ratios, frequency, and failu...
	Powder Wet Vibrating Screen System For Lithium Battery Material Testing	Standard ASTM E11: Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves ISO 3310-1: Test Sieves – Technical Requirements ...

All supplier products

Same products

	Air Permeability Tester STD- F8	Seller: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...
	Surface Performance Tester STD-FB4 - A	Seller: Standard International Group (HK) Limited	Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti...
	Compression Tester STD - FB3 - A	Seller: Standard International Group (HK) Limited	TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar...
	Single - Strand Bending Tester STD - FB2 - SH	Seller: Standard International Group (HK) Limited	Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ...
	Bending Tester STD- FB2 - S	Seller: Standard International Group (HK) Limited	Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig...