Solar Radiation Meters / Solar Radiation Sensors
Product Introduction:
The purpose of this instrument is to measure the temperature change of the sample with radiant heat.
Arrange the sample and its reference material on the sample table, install it on the measuring table at an Angle of 45°, set a heating plate parallel to the measuring table, measure the surface temperature of the two samples with a radiation thermometer, etc., and measure by regression extrapolation method.
Standard:
ISO 9060:2018
ISO 9060
ISO 17025
Product Features:
Sample table or holder designed to accommodate both a test sample and a reference material of a specific size (10 cm x 7 cm).
Mounting system for the sample table positioned at a 45° angle relative to the radiant heat source. The table is likely painted black (as indicated by "black painting" for the measuring table Angle) to standardize its thermal properties.
Parallel heating plate made of aluminum black plate, serving as the controlled radiant heat source.
Heater with a controlled operating temperature (90℃) managed by PID control for stability.
Fixed spacing between the sample station (measuring table) and the heater (15cm).
Requires an external radiation thermometer or thermal imaging system (as noted in the "Attention" section) to measure the surface temperature of the samples non-contact.
Designed to operate within a controlled measuring chamber environment with specified temperature (20$pm$1℃) and relative humidity (50$pm$10%RH).
Includes calibrated components for the measuring table and heater.
Uses a regression extrapolation method for data analysis.
Includes a heater storage box.
Specification parameters:
Model: STD-IT-PT
Sample size: 10 X 7cm
Compare sample size: 10 X 7cm
Heater: Aluminum black plate
Heater operating temperature: 90℃
Heater control mode: PID control mode
Measuring table Angle: 45 degrees (black painting)
Sample station/heater spacing: 15cm
Equipment calibration: Measuring table (including sample mounting rack and sample table)
Heater (including temperature controller)
Heater storage box
Measuring chamber conditions: 20±1℃， 50± 10%RH
Power supply: AC100V or 220v (using downlink transformer)， 50hz or 60hz
Send product request
Other supplier products
 |
Water bath indentation hardness tester / Indentation Resistance Tester | Product Introduction: Water bath indentation hardness tester is used to determine the indentation hardness of extruded polyethylene anticorrosive ... |
 |
Camera test light box ISO 12233 | Standard ISO 12233: Compliant with SFR (Spatial Frequency Response) testing for lens resolution. IEC 62679: Photometric requirements for video ca... |
 |
Guidewire Pushing Force Tester ASTM F | Standards YYT0807 - 2010 YY/T0663.2 - 2016 ASTMF2394 - 2007 Main Uses The guidewire pushing force tester is a precision testing tool in the med... |
 |
Plastic Pipe Hydrostatic Pressure Burst Tester | Standard ISO 1167: For thermoplastics pipe systems under constant internal pressure. ASTM D 1598: Standard test method for time-to-failure of pla... |
 |
STD G651 national standard shoe bending tester | Product Introduction: National standard shoe bending testing machine is specialized in testing finished shoes and soles, after a long time, fixed ... |
Same products
 |
Bottle Wall and Bottom Thickness Tester | Seller: Standard International Group (HK) Limited | The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha... |
 |
Pinhole Tester / Pinhole Testing Equipment | Seller: Standard International Group (HK) Limited | The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ... |
 |
Cork Puncture and Chip Detection Instrument | Seller: Standard International Group (HK) Limited | The rubber stopper puncture debris detector is a device specifically used to detect the number of... |
 |
Aluminum Ointment Tube Toughness Tester | Seller: Standard International Group (HK) Limited | The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind... |
 |
Vacuum leak tester / Vacuum leak instrument | Seller: Standard International Group (HK) Limited | Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott... |
