.

PLC liquid crystal touch impact testing machine (simple suspension)

Product Introduction:

Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile), reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.

Standards:

GB/T 11022-2020. GB/T 3906-2020. JB/T 10840-2008.GB/T 7251.1-2013 ,GB/T 7251.4-2017.GB/T 7251.5-2017 ,GB/T 20641-2014

GB/T 20138-2006 ,GB/T2423.55-2006 ,Q/GDW11008-2013

Main features:

Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.

Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.

Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.

Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.

Performance parameters:

1. Simple beam impact testing machine

- Impact speed: 2.9m/s

- Impact energy: 1/2/4/5J

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 230mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

2. Cantilever beam impact testing machine

- Impact speed: 3.5m/s

- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J(3 hammers, customer's choice)

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 335mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)


Send product request

To: Standard International Group (HK) Limited
Your E-mail:
Message text:


Send to other suppliers

Other supplier products

Multi-Finger Scratch/Mar Tester
Multi-Finger Scratch/Mar Tester Standards Chrysler LP-463DD-18-01 Scratch and Mar Resistance of Automotive Plastics Chrysler PF-10938 Scratch and Mar - Resistance of Molded-In-C...
Fabric sensory quality evaluation tester
Fabric sensory quality evaluation tester Product innovation: The "feel and look", or so-called "sensory perception", of fabrics and knitted fabrics, nonwovens, paper products, leather and...
Washing Fastness testing machine | Washing Fastness Tester
Washing Fastness testing machine | Washing Fastness Tester G228B washing fastness tester is used for washing, dry-clean color fastness testing. Electric touch switch, LCD menu display, without mechanical co...
Rubber Mooney Viscosity Tester 丨Mooney Viscometer
Rubber Mooney Viscosity Tester 丨Mooney Viscometer Test principle: The Mooney viscometer is used to measure the viscosity of rubber under specific conditions. In the test, the rubber sample was loa...
Snap Button Tester | Button Snap Pull Tester
Snap Button Tester | Button Snap Pull Tester Standard ASTM D7142-2/F963: Standard Consumer Safety Specification for Toy Safety CFR 1500: Consumer Product Safety Commission (CPSC) Hazardous S...
All supplier products

Same products

Bottle Wall and Bottom Thickness Tester
Bottle Wall and Bottom Thickness Tester Seller: Standard International Group (HK) Limited The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha...
Pinhole Tester / Pinhole Testing Equipment
Pinhole Tester / Pinhole Testing Equipment Seller: Standard International Group (HK) Limited The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ...
Cork Puncture and Chip Detection Instrument
Cork Puncture and Chip Detection Instrument Seller: Standard International Group (HK) Limited The rubber stopper puncture debris detector is a device specifically used to detect the number of...
Aluminum Ointment Tube Toughness Tester
Aluminum Ointment Tube Toughness Tester Seller: Standard International Group (HK) Limited The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind...
Vacuum leak tester / Vacuum leak instrument
Vacuum leak tester / Vacuum leak instrument Seller: Standard International Group (HK) Limited Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott...