Wrinkle Recovery Tester
The main principle of the wrinkle recovery tester is to apply a predetermined pressure to the specimen under standard atmospheric conditions and to maintain the specified time. The overall structure of the instrument and the precise spiral column ensure that the loaded specimens produce a uniform deformation. After removing the sample from the instrument, re-adjust the sample under standard atmospheric conditions and allow it to recover for a certain period of time, and then compare the sample with the reference sample to assess the appearance of the sample.
The instrument consists of a base with a bracket, the base of the fixed steel plate and the top of the movable steel plate to match ,the activities of the flange with the locking pin. Equipped with four standard weights, respectively, 2000g, 1000g, 500kg, 200kg.
Application
The instrument consists of a base with a bracket, the base of the fixed steel plate and the top of the movable steel plate to match ,the activities of the flange with the locking pin. Equipped with four standard weights, respectively, 2000g, 1000g, 500kg, 200kg.
Application
The wrinkle recovery test instrument detects the recovery of the specimen after a certain period of time under a load. It is suitable for any fiber pure or blended fabric test. Besides, it can not maintain the shape of stable materials under the characteristics of the conditions, such as the material which is soft, thin and easy to bend. We can evaluate its anti-crease performance through this device.
Technical Parameters
Standards:
AATCC 128Wrinkle recovery of fabrics: Appearance method
ISO 9867Textiles - Evaluation of the wrinkle recovery of fabrics - Appearance method
ENKA 306International standard that specifies the methodology for evaluating thewrinkle recovery performanceof textiles, particularly for fabrics prone to deformation under pressure
ISO 9867Textiles - Evaluation of the wrinkle recovery of fabrics - Appearance method
ENKA 306International standard that specifies the methodology for evaluating thewrinkle recovery performanceof textiles, particularly for fabrics prone to deformation under pressure
Accessories:
(1)First ,use the pressure sample device, three samples are tested continuously. The interval is about 1min;
(2)Fold the sample face to face. Cloth edge clip with a clip, not more than 5mm;
(3)In some cases the sample surface will be stained together. We should use a piece of paper or aluminum foil whose size is 18x14mm. Be careful not to contact the sample by hand;
(4)Place the folded sample between the two briquettes and apply the weight immediately. Turn on the chronograph and wait 60 + 2 seconds. Prepare the next sample according to 2,3,4 steps.
(5)After 5 minutes, remove the first piece of weight quickly and easily. Transfer the folded sample with the clip to the sample rack of the measuring instrument;
(6)Remove the paper or aluminum foil. Place one side of the sample in the sample holder and the other side is the free hanging. After 60 +2 seconds, Put the second and third pieces of samples into the sample folder;
(7)Adjust the instrument so that the hanging end of the sample is consistent with the vertical mark of the instrument, within 5min should be constantly adjusted (so that the hanging end of the sample is consistent with the vertical mark of the instrument,) to avoid the impact of gravity;
(8)After 5 minutes, record the recovery angle of the sample. If the sagging side is slightly curled or twisted to pass through the vertical plane of the center of the droop and the axis of the dial as a reference for the crease return angle reading;
(9)Repeat the above steps, and then do three negative fold of the sample and the zonal frontal fold and the opposite fold (a total of 12).
(2)Fold the sample face to face. Cloth edge clip with a clip, not more than 5mm;
(3)In some cases the sample surface will be stained together. We should use a piece of paper or aluminum foil whose size is 18x14mm. Be careful not to contact the sample by hand;
(4)Place the folded sample between the two briquettes and apply the weight immediately. Turn on the chronograph and wait 60 + 2 seconds. Prepare the next sample according to 2,3,4 steps.
(5)After 5 minutes, remove the first piece of weight quickly and easily. Transfer the folded sample with the clip to the sample rack of the measuring instrument;
(6)Remove the paper or aluminum foil. Place one side of the sample in the sample holder and the other side is the free hanging. After 60 +2 seconds, Put the second and third pieces of samples into the sample folder;
(7)Adjust the instrument so that the hanging end of the sample is consistent with the vertical mark of the instrument, within 5min should be constantly adjusted (so that the hanging end of the sample is consistent with the vertical mark of the instrument,) to avoid the impact of gravity;
(8)After 5 minutes, record the recovery angle of the sample. If the sagging side is slightly curled or twisted to pass through the vertical plane of the center of the droop and the axis of the dial as a reference for the crease return angle reading;
(9)Repeat the above steps, and then do three negative fold of the sample and the zonal frontal fold and the opposite fold (a total of 12).
Technical Parameters
| Items | Parameters |
| Sample size | 15cm×28cm(6×11inch) |
| Weights | 2000g，1000g，500kg，200kg Accumulate |
| Dimensions | 150×150×330mm(L×W×H) |
| Weight | 9.5kg(21lb) |
Send product request
Other supplier products
 |
Rubber hose outer coating wear testing machine | Product Introduction: Rubber hose outer coating Wear testing machine for hydraulic hoses and other similar types of hoses with fabric or steel wir... |
 |
20L Spherical Explosion Tester | Product Description: 20L Spherical Explosion Tester is characterized by accurate test data and ease of use. Its through the compressed air will be... |
 |
Standard light source sample table meter | Standards ISO 3664:2009: Meets international standards for graphic arts and photography view conditions. DIN 6173-2: European norm for illuminant... |
 |
SI80 Carbon Arc Aging Tester丨SI80 Carbon Arc Aging device | Material aging and fading performance test SI80 carbon arc aging tester, carbon arc aging machine through AC light carbon rod, produce arc light, ... |
 |
Bundle wire and cable burning tester | Introduction： The Bundle Wire and Cable Burning Test Machine is a vital instrument for assessing the fire safety of multiple wires and cables when... |
Same products
 |
Liquid Sliding Penetration Comprehensive Performance Tester | Seller: Qinsun Instruments Co., LTD | G373 Liquid penetrating and strike-through comprehensive performance tester - Penetrability test ... |
 |
Nonwovens liquid loss tester | Seller: Qinsun Instruments Co., LTD | Nonwovens liquid loss tester built-in loss of Taiwan and sample fixture for non-woven fabric mate... |
 |
Elmendorf Tearing Strength Tester | Seller: Qinsun Instruments Co., LTD | G008 Manual Tearing Tester - Material Tear Resistance Test G008Manual Tearing Tester, The Elmend... |
 |
Dry Cleaning & Washing Cylinder | Seller: Qinsun Instruments Co., LTD | IntroductionThe dry cleaning and washing cylinder consists of a stainless steel rotary test chamb... |
 |
Rotary Rubbing Color Fastness Tester (Crockmeter) | Seller: Qinsun Instruments Co., LTD | Standard AATCC 116: Colorfastness to Crocking (American Association of Textile Chemists and Co... |
