Thermal Protective Performance Tester (TPP)
The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through a protective composite fabric system - measuring the resulting damage to human skin. Standards： BS EN ISO 6942. EN 366. EN 407. ISO 11612. ASTM F1939. ASTM F2702. NFPA 1971. NFPA 2112. GB 38543. GB/T 38306 Feature： Industrial personal computer with analysis software is suitable for severe testing conditions. Automatic calculation for heat transmission factor and radiant heat transfer index. Sample holder with force applied kit is easy to operate. Single pump for shutter movement and cooling water loop. TPP Specifications： • Up to 7.5 in x 7.5 in. (19 cm x19 cm) sample size • Copper slug calorimeter sensors (ASTM or ISO) • ± 0.75°C temperature measurement • ± 3% radiant heat flux measurement • Device Dimensions: 42 in. x 20 in. x 18 in. (107 cm x 51 cm x 46 cm) • Space Requirements: 46 in. x 26 in. x 24 in. (117 cm x 67 cm x 61cm) • Power Requirements: 208-265 VAC, 50/60Hz, Single-phase • Maximum nominal current 20 Amps • Compressed Air: Clean/dry air at 70-90 PSI, (145 PSI max) • Cooling Water: Cooling water required, chiller or tap water source is acceptable • Propane Requirement: Regulated supply at 15 PSI (minimum) • Water-cooled radiant heat source with 9 quartz (500W) infrared lamps • Two gas burners with flame detection auto ignition • Mass flow controller for precise gas control • Water-cooled protective shutter • Pneumatic sample carriage and shutter assembly • Integrated sensor cooling stand (air cooled) • Emergency stop cuts gas flow, power to lamps and pneumatics • Tinted tempered glass shield protects operator • Software safety interlocks monitor water flow, carriage position, burner ignition
Send product request
Other supplier products
 |
Automotive wire cyclic bending testing machine | StandardThis testing machine aligns with global automotive industry standards for wire harness reliability, includingISO 6722(Road vehicles –... |
 |
G650D Finished shoe bending tester (heel lift) | Product Introduction: The finished shoe resistance zigzag tester drives the zigzag part of the finished shoe to zigzag repeatedly with the zigzag ... |
 |
Crosshatch scratch tester | Crosshatch scratch tester/Scratch tester makes contacting relative motion between the scratching head and material surface for the evaluation of th... |
|
|
Thermal Protective Performance Tester (TPP) | The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through... |
 |
MST clothing pressure tester | The MST Clothing Pressure Tester/Underwear Pressure tester is used in the body or in the laboratory to easily measure the pressure of elastic band... |
Same products
 |
Liquid Sliding Penetration Comprehensive Performance Tester | Seller: Qinsun Instruments Co., LTD | G373 Liquid penetrating and strike-through comprehensive performance tester - Penetrability test ... |
 |
Nonwovens liquid loss tester | Seller: Qinsun Instruments Co., LTD | Nonwovens liquid loss tester built-in loss of Taiwan and sample fixture for non-woven fabric mate... |
 |
Elmendorf Tearing Strength Tester | Seller: Qinsun Instruments Co., LTD | G008 Manual Tearing Tester - Material Tear Resistance Test G008Manual Tearing Tester, The Elmend... |
 |
Dry Cleaning & Washing Cylinder | Seller: Qinsun Instruments Co., LTD | IntroductionThe dry cleaning and washing cylinder consists of a stainless steel rotary test chamb... |
 |
Rotary Rubbing Color Fastness Tester (Crockmeter) | Seller: Qinsun Instruments Co., LTD | Standard AATCC 116: Colorfastness to Crocking (American Association of Textile Chemists and Co... |
