Thermal Protective Performance Tester (TPP)
The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through a protective composite fabric system - measuring the resulting damage to human skin. Standards： BS EN ISO 6942. EN 366. EN 407. ISO 11612. ASTM F1939. ASTM F2702. NFPA 1971. NFPA 2112. GB 38543. GB/T 38306 Feature： Industrial personal computer with analysis software is suitable for severe testing conditions. Automatic calculation for heat transmission factor and radiant heat transfer index. Sample holder with force applied kit is easy to operate. Single pump for shutter movement and cooling water loop. TPP Specifications： • Up to 7.5 in x 7.5 in. (19 cm x19 cm) sample size • Copper slug calorimeter sensors (ASTM or ISO) • ± 0.75°C temperature measurement • ± 3% radiant heat flux measurement • Device Dimensions: 42 in. x 20 in. x 18 in. (107 cm x 51 cm x 46 cm) • Space Requirements: 46 in. x 26 in. x 24 in. (117 cm x 67 cm x 61cm) • Power Requirements: 208-265 VAC, 50/60Hz, Single-phase • Maximum nominal current 20 Amps • Compressed Air: Clean/dry air at 70-90 PSI, (145 PSI max) • Cooling Water: Cooling water required, chiller or tap water source is acceptable • Propane Requirement: Regulated supply at 15 PSI (minimum) • Water-cooled radiant heat source with 9 quartz (500W) infrared lamps • Two gas burners with flame detection auto ignition • Mass flow controller for precise gas control • Water-cooled protective shutter • Pneumatic sample carriage and shutter assembly • Integrated sensor cooling stand (air cooled) • Emergency stop cuts gas flow, power to lamps and pneumatics • Tinted tempered glass shield protects operator • Software safety interlocks monitor water flow, carriage position, burner ignition
在线联系供应商
Other supplier products
 |
Plastic carbon black dispersion determination tester | Scope of application: DW1431 plastic carbon black dispersion measurement system is based on a professional image acquisition system and correspond... |
 |
Battery diaphragm permeability tester | Technical parameters: Test range: 10-15000s/100ml（standard configuration） Other ranges are optional. Resolution: 0.1s/100ml Pressure accuracy: 0... |
 |
Safety Helmets Impact and Penetration Resistance Tester | Standard GB/T 2811-2019(China’s national standard for helmet safety and impact resistance) GB/T 2812-2006/XXXX(Testing methods for impact... |
 |
Guide pin anchoring force tester | Product introduction The anchoring force test of the guide needle can ensure the anchoring effect of the mammary positioning filament within the t... |
 |
Cantilever Fabric Stiffness Tester | Application: Fabric Stiffness Tester, is a practical equipment to determine the bending height, flexural rigidity and bending modulus of fabrics. ... |
Same products
 |
Liquid Sliding Penetration Comprehensive Performance Tester | 卖方: 上海千实精密仪器 | G373 Liquid penetrating and strike-through comprehensive performance tester - Penetrability test ... |
 |
Nonwovens liquid loss tester | 卖方: 上海千实精密仪器 | Nonwovens liquid loss tester built-in loss of Taiwan and sample fixture for non-woven fabric mate... |
 |
Elmendorf Tearing Strength Tester | 卖方: 上海千实精密仪器 | G008 Manual Tearing Tester - Material Tear Resistance Test G008Manual Tearing Tester, The Elmend... |
 |
Dry Cleaning & Washing Cylinder | 卖方: 上海千实精密仪器 | IntroductionThe dry cleaning and washing cylinder consists of a stainless steel rotary test chamb... |
 |
Rotary Rubbing Color Fastness Tester (Crockmeter) | 卖方: 上海千实精密仪器 | Standard AATCC 116: Colorfastness to Crocking (American Association of Textile Chemists and Co... |
