Chemical Reactor Cleaning System
Total ChemicalReactor Cleaning Systems
Reactor Cleaning Systems are designed to safely and effectively peel and clean scale stuck to the inside of polymerization tanks, reactors, and storage tanks by using high-pressure water. We design and manufacture all the relevant items for the system such as high-pressure pump, cleaning device, nozzle, and controller etc.
Because of various complex structures such as agitator shaft, it has always been a difficult point in the industry to realize cleaning without dead angle. Due to the following disadvantages of manual cleaning, the cleaning effect can not meet the requirements well all the time:
① Manual operation requires hand-held cleaning, which has the characteristics of high labor intensity, long cleaning time and bad working environment;
② Due to various production processes, there may be toxic or harmful gases in the reactor, which will cause great damage to human body, and even affect human body when cleaning with cleaning solution;
③ The inside of the reactor may be a flammable and explosive working environment, so manual cleaning is dangerous;
④ Because the cleaning method is man-made, the cleaning effect may be greatly affected by human factors;
⑤ Every year, there are reports of casualties in manual cleaning, which has a great impact on the enterprise society and has a great hidden danger;
⑥ Because the reactor generally has mixing shaft, mixing blade, coil, stiffener and other heterogeneous parts, manual cleaning is also difficult
⑦ Because some materials in the reactor are easy to dry and form film, which makes it difficult to clean, the cleaning time is particularly important after the materials in the reactor are emptied.
Working principle：
The setting degree of the system can realize one key operation and high automation degree. The automatic reactor cleaning equipment can clean the parts that are difficult to clean, such as the back, bottom and upper head of the mixing shaft. The high pressure water jet is ejected from the high pressure tank cleaning nozzle to realize the cleaning of this position. Generally, 2-4 cleaning points (which can be set by themselves and adjusted according to the actual situation) are set on the mixing shaft after cleaning one side of the mixing shaft. The pipe coiler is recovered to the original point, and then the arm is swing to the other side of the mixing shaft. The same cleaning method as on the left side sets different cleaning points according to the actual needs, and automatic fixed-point cleaning. Each cleaning point can set the cleaning time as required.
Send product request
Other supplier products
 |
High Temperature Oxygen Index Tester | Application Evaluating material combustion performance in R&D. Quality control for product acceptance. High-temperature safety assessment in... |
 |
Car seat components strength test bench | Applicable standards: GB 15083：Itspecifies the strength requirements and test methods of the car seat system, which is applicable to the seats and... |
 |
Wyzenbeek or Oscillatory Abrasion Tester-QINSUN | Product introduction: Wyzenbeek wear resistance tester, also known as Oscillatory wear resistance tester, is used to test the wear resistance of f... |
 |
Children's Product Comprehensive Force Tester | Applicable Standards GB/T 31701 - 2015. GB/T 6675 - 2003. GB/T 32599. EN71 - 1. BS 7909. ASTM F963. 16CFR1500.51. GB/T 22704. etc. Application Sc... |
 |
Nissan 4-Station Abrasion Tester for Multi-Material Durability Tester-QINSUN | Standard ASTM D3884(Standard Guide for Abrasion Resistance of Textile Fabrics) ISO 5470-1(Rubber- or Plastics-Coated Fabrics - Abrasion Resistanc... |
Same products
 |
Seat Bumping and Creep Test Bench | Seller: Standard International Group (HK) Limited | This test bench is used for simulating the car seat bumping and creep situation when a car is run... |
 |
Automobile seat belt fixed point test bench | Seller: Standard International Group (HK) Limited | Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtur... |
 |
Impact strength tester for car seat headrest | Seller: Standard International Group (HK) Limited | Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requi... |
 |
Impact strength tester for car seat launching headrest | Seller: Standard International Group (HK) Limited | Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, w... |
 |
Automobile Headrest Strength Tester | Seller: Standard International Group (HK) Limited | Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test me... |
