Strip evenness tester

• 

Product Information:

Cotton yarn fiber strip analyzer is a high performance, high test efficiency of textile laboratory instrument, it is used to test the fine yarn, roving, sliver trunk density uneven, analysis of the cause of uneven, suitable for cotton, wool, hemp, chemical fiber short fiber pure spinning and blended yarn strip dry test.

Main parameters:

1. Capacitor detection slot: 4

2. Test range: 4tex —— 80k tex

3. Test speed: 8, 25, 50, 100, 200, 400, 800m/min

4. Test time: 10sec —— 20min can be set arbitrarily

5.CV%, U% value range: 0.2% —— 100%

6. Variation - Length curve: Cutting length 1 cm —— 1000m

7. Output three types of 12-speed defects at the same time:

Details -30%, -40%, -50%, -60%

Coarse section +35%, +50%, +70%, +100%

Cotton knot +140%, +200%, +280%, +400%

8. Spectral diagram: 170 channels, wavelength range 1cm-2000m

9. Linear density frequency distribution: -100% —— +100%, +100% —— +400%

10.DR% value: Output DR（1m, +5%）， DR（1m, -5%）， DR（20cm, +35%）， DR（20cm, -30%） four DR% values

11. Number of batch measurements: ≤20

12. Power supply: AC220V±10%50Hz±5Hz

13. Power consumption ≤400VA

Другие товары поставщика

	Mask Flame Flammability Tester	introduction: The flame-retardant tester of medical mask is used to test the flame-retardant performance of the mask when it is accidentally conta...
	Helmets Vertical SpacingInfrared - positioning Tester/ safety helmet vertical spacing tester / helmet fit measurement device	Purpose This measuring instrument is used to measure the vertical spacing and wearing height of safety helmets. Applicable Standard GB/T 2812-...
	TABER 5750 Abrasion Tester ISO 9352 ISO 5470-1	Standards: ASTM D3884 、 ASTM D1175 、 ASTM D1044 、 ASTM D4060 、 TAPPI T476 、 ISO 9352 、 ISO 5470-1 、 JIS K7204 、 JIS A1453、 JIS K6902 、 JIS L1096 、...
	Seam Fatigue Tester	Seam Fatigue Tester - Automotive Interior - standard Standards: Toyota TSL5101G Section 3.7, GMW 3405, Nissan M-0154, Ford Motor Co. BN 106-02,...
	scratch resistant instrument	scratch resistant instrument - Material and Parts of Automotive - standard Standards: GB/T 2918,GB/T 6151,GB/T 8424.3,PV3952,BMW GS97034-2,BMW ...

Похожие товары

	Falling Sand Abrasion Test machine	Продавец: Standard International Group (HK) Limited	The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance...
	Conveyor Belt Drum Friction Testing Machine	Продавец: Standard International Group (HK) Limited	Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes...
	Dry Sand Rubber Wheel Wear Tester	Продавец: Standard International Group (HK) Limited	The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater...
	Sliding Bearing Fatigue Testing Machine	Продавец: Standard International Group (HK) Limited	The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua...
	High temperature vacum friction & wear tester	Продавец: Standard International Group (HK) Limited	The working principle of a high-temperature vacuum friction and wear testing machine is to simula...