Drossing Flux
Drossing Flux (SATA-PF-310)
Description of Drossing Flux (SATA-PF-310)
SATA drossing fluxis specially developed for removing the slag from the aluminium melt before or after refining procedure. It is for in- furnace use. The slag after treatment is dry ,loose, easy to be removed.
Apperance: White or gray white in powder
Application temperature: 700-780 ℃
a)More choice for your option,
b)1. Sodium-free drossing flux which suitable for High magnesium al-alloy.
c)2. Eco-friendly aluminium drossing fluxwith less emission
Advantage of Drossing Flux (SATA-PF-310)
Mild Exothermic flux; separate the aluminium with the dross. Decomposition of alumina in slag, to make the slag dry and loose, easy for removing.
Enhance the aluminium melt purity, improve the alloy properties greatly, and reduce metal loss.
Reduce the slag formed on the furnace linings and bottom. Damage of furnace can be avoided. Increase the service life of furnace. Save the labor and power loss in furnace cleaning due to frequency of cleaning is minimized.
Sodium free drossing flux can avoid the white spot to be occurred on the surface of alumininum and its alloy.
Eco-friendly drossing flux with less emission is benefit for workers, enviorment with high efficiency.
Package of Drossing Flux (SATA-PF-310)
- ～25kg PP bag or 20-25kg cartons.
Dosage of Drossing Flux (SATA-PF-310)
Storage of Drossing Flux (SATA-PF-310)
Store in a dry and cool place with good ventilation. Original packing should be kept until ready to use.
Send product request
Other supplier products
 |
Covering Flux | General Introduction: Chemical formular: Mgcl2 6H2O Purity: 46.00%min. Appearance: pure white crystal power CAS NO.:7791-18-6 Chemically, is repr... |
 |
Reclaimed Fluxes | General Description of Reclaimed Fluxes Reclaimed fluxes is a strongly exothermic flux and used as covering and drossing flux, recovery of grindin... |
 |
Raw Materials | Metallurgical flux coating materialrefers to the material which can separate metal from mineral by forming a low melting point slag layer while int... |
 |
Mg Alloy Flux | Magnesium alloyfluxhas a low melting point and small heat capacity. When heated in the air, it gets oxidized fast, and it is easy to burn when over... |
 |
Magnesium Chloride Anhydrous | Anhydrous magnesium chloride is our main raw materials for producing foundry fluxes, it is a byproduct of titanium sponge from the three largest ti... |
Same products
 |
LUBE SH-ONE-4S 400G for Fanuc Machines | Seller: Guangdong Juguangheng Automation Equipment Co.,Ltd. | Lubecorp part number 249250 is a 400ml bellows style cartridge often times used in autolube appli... |
 |
Mobil Grease 28 Synthetic Aviation Grease | Seller: Guangdong Juguangheng Automation Equipment Co.,Ltd. | Mobil grease 28is a high performance, antiwear grease. Available as a cartridge,2kgcan, 16kg pail... |
 |
Kluber Isoflex Topas NCA 5051 50ml Original Lubricants | Seller: Guangdong Juguangheng Automation Equipment Co.,Ltd. | ISOFLEX TOPAS NCA 5051is a beige synthetic long homogeneous and short fiber. It consists of a syn... |
 |
CHRISTO-LUBE MCG 111 2-OZ Valve Seal Grease | Seller: Guangdong Juguangheng Automation Equipment Co.,Ltd. | Christo-Lube®MCG 111is a fully fluorinated grease thickened with PTFE which operates under ex... |
 |
Permatex 81160 85G High Temperature Resistant Resin | Seller: Guangdong Juguangheng Automation Equipment Co.,Ltd. | Permatex 81160 High-Temp Red RTV Silicone Gasket, 3 oz |
