Midsole Fibreboard Bending Test Machine

Product Introduction:

G664 mid-sole fiberboard zigzag testing machine Test leather shoes and casual shoes, walking shoes and other travel shoes, mid-sole fiberboard zigzag resistance quality.

One end of the sample of shoe fiberboard material is hung in a weight, and one end is fixed in the fixture is continuously reciprocated to the left and right each bending 90 degrees, testing a certain number of times until the break, the number of breaks to determine the flexion index of the bottom plate, as a basis for comparison and selection of the bottom plate.

Reference standard:

QB/T 1472. BS 5131:4.2. SATRA TM3. PM4. PM5. PM6. PM15. PM16. QB/T4329-2012 standard

Product Advantages:

Measures Key Durability: Quantifies the resistance of mid-sole fibreboard to repeated bending and fatigue cracking under tension.

Standard Compliant: Designed to meet relevant national and international standards for testing fibreboard and footwear components (QB/T 1472. BS 5131. SATRA TM3. etc.).

Quantitative Result: Provides an objective numerical result (cycles to break/flexion index) for comparing material performance.

Multiple Testing Stations: Allows simultaneous testing of 6 samples, significantly increasing testing throughput.

Controllable Test Parameters: Enables precise control of the bending angle, speed, and applied tension (via the weight).

Automatic Counting: The integrated counter automatically tracks the number of cycles until sample failure.

Precise Speed Control: The variable frequency motor ensures stable and accurate flexing speed.

Product Features:

Multiple test fixtures/stations (6) for simultaneous testing.

Clamping mechanism at one end of each station to fix the fibreboard sample.

System at the other end of each station to attach a weight (approx. 2kg including clamp) to apply tension to the sample.

Mechanism for continuous reciprocating bending of the samples through a 90° angle.

Controllable flexing speed (60 ± 10 r/min) driven by a variable frequency motor.

LCD digital counter for each station (up to 999.999 cycles) to record cycles to sample break.

Sample holders with specified upper and lower clip lengths (15mm and 10mm) to hold the 80x10mm test piece.

Designed for testing fibreboard samples of a specific size (80x10mm).

Technical specifications:

1. Test fixture: 6

2. Test piece: 80×10mm

3. Reciprocating Angle: 90°

4. The weight includes the clamp: (2±0.01kg)×6

5. Tortuous speed: (60±10)r/min

6. Counter: LCD, 0——999999(7 groups)

7. Sample holder: upper clip length 15mm, lower clip length 10mm

8. Motor: variable frequency motor

9. Volume: 109×26×34cm

10. Power supply: 1∮，AC220V,3A

Other supplier products

	Battery Powder resistivity meter	Product Advantages Unmatched Measurement Flexibility Dual-probe compatibility: Switch seamlessly betweenfour-point probe(for low-resistance m...
	Safety shoe impact testing machine	According to the criteria: Bs-953,1870,EN-344,ANSI-Z41,CSA-Z195 ISO K88782 Product Advantages: Measures Critical Safety Property: Quantifies t...
	Sliding Bearing PV Tester	Standard This machine is mainly applicable to GB 7948-1987 plastic bearing limit PV test method, JB/T 7381-2010 powder metallurgy oil bearing PV v...
	Respirator Fit Tester	Applications: Overall Mask Leakage Test: Mask leakage is measured while the mask is challenged with an aerosol, with or without a plugged filter...
	Total Knee Joint Prostheses Wear Tester	Standard ISO 14243-1:2014: Specifies wear testing parameters for total knee prostheses, including axial loading, flexion/extension kinematics, a...

All supplier products

Same products

	Scott Flex Tester	Seller: Standard International Group (HK) Limited	Product Introduction: Scott kneading tester is suitable for back and forth kneading resistance o...
	NEU nanofiber electrospinning device	Seller: Standard International Group (HK) Limited	Content The Nanofiber Electrospinning Unit uses electrospinning techniques to safely and easil...
	KK03 Scratch tester	Seller: Standard International Group (HK) Limited	Product Introduction: With the continuous expansion of the use of plastic molding products, from...
	KK02 Scratch tester	Seller: Standard International Group (HK) Limited	Product Introduction: With the continuous expansion of the use of plastic molding products, from...
	KK01 Scratch tester	Seller: Standard International Group (HK) Limited	Product Introduction: With the continuous expansion of the use of plastic molding products, from...