ROSS zigzag tester
Product Introduction:
The ROSS zigzag resistance tester installed the sole strip test piece on the ROSS zigzag test machine, so that the cut is directly above the center of the rotating shaft of the ROSS zigzag test machine, and drove the test piece to perform free 90-degree zigzag on the shaft through the ROSS zigzag test machine. After a certain number of tests, the length of the test piece incision is measured. The zigzag resistance of the test piece was evaluated by the size of the notch growth rate.
Reference standard:
GB/T2099-2007. ASTM-D1052. ISO-5423. SATRA TM60. HB-T2411HG/ T2411 and other standards
Product Advantages:
Measures Key Durability: Quantifies the resistance of sole materials to flex cracking and notch growth, a vital indicator of footwear lifespan.
Standard Compliant (ROSS Method): Designed to meet numerous relevant international and national standards (ASTM D1052. SATRA TM60. etc.) specifically for the ROSS flex test.
Quantitative Result: Provides objective data based on the measured growth rate of the pre-cut notch.
Multiple Testing Stations: Allows simultaneous testing of multiple test pieces (12), significantly increasing testing efficiency.
Controllable Test Parameters: Enables precise setting and control of the bending angle (90$pm$2º) and flexing speed (0-100 r/min).
Automatic Stop Function: Can be set to stop automatically after a specified number of test cycles.
Suitable for Sole Materials: Specifically designed for evaluating the flex fatigue characteristics of sole strips.
Technical parameters:
1. simultaneous measurement: (12 test pieces)
2. bending Angle: 90±2º
3. speed: 0-100r/min can be switched.
4. controller: LED-SLD806 integrated display control function
5. hole punch: 2.5mm
6. Test mode; Automatic stop when the test time is reached
7. fixture features: can test the sole at the same time can test pieces
8. zigzag shaft diameter: 10mm.
9. sample method: sole test piece
10. sample size: 152×25mm
11. Power supply: AC220V,10A
Random configuration:
1. One machine
2. 1 knife die
3. One power cable
4. One cutting knife
5. One copy of instructions
6. One delivery note
Send product request
Other supplier products
 |
Pump and Valve Contamination Tolerance Tester | Meet the standard: ISO 4406 ISO 18413 ISO 10707 ISO 6403 ISO 10372 NFPA T2.6.1 Product Introduction: Solid particle contamination is a maj... |
 |
Respiratory Resistance Tester | Standards: · GB/T 2626-2006 Respiratory protective equipment -- non-powered air-purifying particle respirator - 6.5 6.6 · GB/T 326... |
 |
Digital Fabric Thickness Gauge | Standards: Standards ASTM D1777 Standard test method for thickness of textile materials GB/T 3820 Determination of thickness of textiles and tex... |
 |
Helmets Vertical SpacingInfrared - positioning Tester/ safety helmet vertical spacing tester / helmet fit measurement device | Purpose This measuring instrument is used to measure the vertical spacing and wearing height of safety helmets. Applicable Standard GB/T 2812-... |
 |
Helmets Acceleration Impact & Penetration Tester | Standard GB/T 2812: Safety Helmets (China National Standard) Equivalent Compliance: ISO 6220-1 (Industrial Safety Helmets – Impact Absorp... |
Same products
 |
Scott Flex Tester | Seller: Standard International Group (HK) Limited | Product Introduction: Scott kneading tester is suitable for back and forth kneading resistance o... |
 |
NEU nanofiber electrospinning device | Seller: Standard International Group (HK) Limited | Content The Nanofiber Electrospinning Unit uses electrospinning techniques to safely and easil... |
 |
KK03 Scratch tester | Seller: Standard International Group (HK) Limited | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
 |
KK02 Scratch tester | Seller: Standard International Group (HK) Limited | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
 |
KK01 Scratch tester | Seller: Standard International Group (HK) Limited | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
