ROSS zigzag tester
Product Introduction:
The ROSS zigzag resistance tester installed the sole strip test piece on the ROSS zigzag test machine, so that the cut is directly above the center of the rotating shaft of the ROSS zigzag test machine, and drove the test piece to perform free 90-degree zigzag on the shaft through the ROSS zigzag test machine. After a certain number of tests, the length of the test piece incision is measured. The zigzag resistance of the test piece was evaluated by the size of the notch growth rate.
Reference standard:
GB/T2099-2007. ASTM-D1052. ISO-5423. SATRA TM60. HB-T2411HG/ T2411 and other standards
Product Advantages:
Measures Key Durability: Quantifies the resistance of sole materials to flex cracking and notch growth, a vital indicator of footwear lifespan.
Standard Compliant (ROSS Method): Designed to meet numerous relevant international and national standards (ASTM D1052. SATRA TM60. etc.) specifically for the ROSS flex test.
Quantitative Result: Provides objective data based on the measured growth rate of the pre-cut notch.
Multiple Testing Stations: Allows simultaneous testing of multiple test pieces (12), significantly increasing testing efficiency.
Controllable Test Parameters: Enables precise setting and control of the bending angle (90$pm$2º) and flexing speed (0-100 r/min).
Automatic Stop Function: Can be set to stop automatically after a specified number of test cycles.
Suitable for Sole Materials: Specifically designed for evaluating the flex fatigue characteristics of sole strips.
Technical parameters:
1. simultaneous measurement: (12 test pieces)
2. bending Angle: 90±2º
3. speed: 0-100r/min can be switched.
4. controller: LED-SLD806 integrated display control function
5. hole punch: 2.5mm
6. Test mode; Automatic stop when the test time is reached
7. fixture features: can test the sole at the same time can test pieces
8. zigzag shaft diameter: 10mm.
9. sample method: sole test piece
10. sample size: 152×25mm
11. Power supply: AC220V,10A
Random configuration:
1. One machine
2. 1 knife die
3. One power cable
4. One cutting knife
5. One copy of instructions
6. One delivery note
在线联系供应商
Other supplier products
 |
BBA steady state solar simulator tester | Standard IEC 61215: Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval IEC 61646: Thin-Film Terrestrial Photo... |
 |
Mask flame retardant tester EN 149 YY 0469 | Standards: GB 19083-2010. EN 149. GB 2626. YY 0469 Applications: Mask Flame Retardant Tester is a special test instrument for flame retardant pe... |
 |
Dental Implants Static Torsion Testing Machine | Standard ISO 13498: Specifies static torsion testing protocols for dental implants, including torque application rates, failure criteria, and da... |
 |
Footwear Flexing Tester | Product Introduction: The finished shoe resistance zigzag tester drives the zigzag part of the finished shoe to zigzag repeatedly with the zigzag ... |
 |
Abrasion Scrubbing Resistance Tester | Content T107 Scrubbing Tester, It is suitable for various abrasion and wet scrubbing tests, which is commonly used in scrubbing resistance tests f... |
Same products
 |
Scott Flex Tester | 卖方: 标准集团 | Product Introduction: Scott kneading tester is suitable for back and forth kneading resistance o... |
 |
NEU nanofiber electrospinning device | 卖方: 标准集团 | Content The Nanofiber Electrospinning Unit uses electrospinning techniques to safely and easil... |
 |
KK03 Scratch tester | 卖方: 标准集团 | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
 |
KK02 Scratch tester | 卖方: 标准集团 | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
 |
KK01 Scratch tester | 卖方: 标准集团 | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
