Steel Bar Testing
The steel bar is rolled by a rolling mill and produce both surface defects and internal defects during the rolling process. The internal defect is that the original defects of the steel chain or billet are extended during the rolling process. These defects are mainly concentrated in the central part of the steel rod. The forms mainly include slag inclusion, shrinkage, delamination, and looseness. The amount of rolling deformation increases and increases. In actual production, these internal defects of the steel rod have a serious impact on the performance of the steel. For example, steel rods used for forging, these internal defects will continue to exist inside the steel rod during the forging process, and some will continue to extend. Some will form a mezzanine. Therefore, the non-destructive testing of the internal defects of steel bars has attracted more and more attention.
Ultrasonic automatic detection system for steel bars
The ultrasonic automatic detection system for steel bars is a device that uses ultrasonic longitudinal wave detection to detect defects such as delamination and inclusions inside the steel bar. The steel rod enters a six-way ultrasonic probe that rotates at a high speed through a communication mechanism, and each channel is set to a different frequency. The steel rod advances at a low speed, so it can cover 100% of the surface of the steel rod. After the steel rod enters the ultrasonic system, the system begins to detect.
When a defect is detected, the probe will feed back the defect signal. The defect signal is processed, amplified, converted to the oscilloscope, and the oscilloscope is transmitted to the computer. The program in the computer responds accordingly, that is, the defect location is identified. In the subsequent production, the marked steel bar will be cut off, thereby avoiding the quality problems caused by the internal defects of the steel bar.
As a non destructive testing equipment manufacturer and supplier, we have been committed to developing and manufacturing high-quality and high-performance NDT equipment to provide customers with the best quality service.
BKNis one of the best ultrasonic testing equipment manufacturers,we have ndt ultrasonic testing equipment,ultrasonic testing of steel barsand steel bar test,RFQ today.
在线联系供应商
Other supplier products
 |
Portable Magnetic Flux Leakage Testing Equipment | MFLequipmentrefers to the formation of a leakage magnetic field on the surface of a test piece after it is magnetized due to defects on the surface... |
 |
Portable Magnetic Flux Leakage Testing Equipment | Magnetic flux leakage test refers to the formation of a leakage magnetic field on the surface of a test piece after it is magnetized due to defects... |
 |
Eddy Current Testing Equipment | Tubing repair is an important measure to reduce the comprehensive cost of production in oil production plants to improve the quality of repairing t... |
 |
EDM Notch | An electric pulse is a pulse generated by electrons, and a pulse is a process of changing a voltage in a short time. Electropulsing is an unsteady ... |
 |
Eddy Current Testing Equipment | Ect testing equipment is a non-contact testing method, which mainly uses the electromagnetic field and electromagnetic induction between metals to ... |
Same products
 |
GT-FM24-PLC填粉机机(3+9+9+3)三导管 | 卖方: 肇庆古雷特科技有限公司 | * 描述 GT-FM-PLC（6-48工位三导管）氧化镁粉灌装机，是在GT-FM-PLC（6-48工位双导管）的基础上改进而成。 双导管灌装机与三导管灌装机的主要区别如下： 三导管灌装机可以在一... |
 |
High Speed Flat Wire Coil Winding Machine for EV Traction Motor Manufacturing | 卖方: Eurion Automation Co., Ltd. | 高精度伺服控制系统：采用工控级电脑控制平台，配套进口伺服电机与减速机，确保运行高效、精准、稳定。 六轴联动结构设计：送线轴、绕线轴、排线轴及手臂成型轴独立控制、协同配合，实现多工序复合成型。 ... |
 |
GT-FM18-PLC灌装机(8+2+8)三导管 | 卖方: 肇庆古雷特科技有限公司 | * 描述 GT-FM-PLC（6-48工位三导管）氧化镁粉灌装机，是在GT-FM-PLC（6-48工位双导管）的基础上改进而成。 双导管灌装机与三导管灌装机的主要区别如下： 三导管灌装机可以在一... |
 |
48工位填粉机 GT-FM48 | 卖方: 肇庆古雷特科技有限公司 | * 描述FM灌装机适用于长长度、不同直径的管式加热器的灌装。 FM填充机填充的加热器具有高密度，根据直径、氧化镁粉末、填充速度，密度可达2.3g/cm3。 FM灌装机有双导管灌装机和三导管灌装机... |
 |
8工位填粉机 GT-FM8 | 卖方: 肇庆古雷特科技有限公司 | * 描述 FM灌装机适用于长长度、不同直径的管式加热器的灌装。 FM填充机填充的加热器具有高密度，根据直径、氧化镁粉末、填充速度，密度可达2.3g/cm3。 FM灌装机有双导管灌装机和三导管灌装... |
