How to Use Tricone Bit Appropriately?

How to Use Tricone Bit Appropriately?

(1) According to the lithology of the drilled formation, the following principles should be followed when selecting the type of drill bit:

(2) In order to optimize the hydraulic parameters of bit, the longer nozzle and unequal diameter combined nozzle bit should be preferred.

(1) Check whether the model and diameter of selected bit meet the requirements;

(2) Carefully check whether the thread, weld and teeth of the drill are in good condition;

(3) Check whether the nozzle is installed firmly and the water hole should be unblocked; when rotating the cone of the rock bit by hand, the bearing seal should be intact; the pressure compensation system of the drill bit should be intact, and the pressure relief hole should not be blocked.

(1) After cleaning the drill thread, apply special thread oil;

(2) Choose a suitable loading and unloading device, and do not jerk when the drill bit is put into the loading and unloading device;

(3) Tighten according to the specified torque;

(4) The drilling operation should be stable, and no hard pressure should be encountered in case of resistance. Drilling of the insert bit should be slow to avoid damage to the alloy teeth in the hard formation and irregular hole;

(5) When drilling down and encountering an obstruction, the depth of the well, the situation and time of the obstruction should be noted, so as to determine the cause of the obstruction and control the working time;

(6) Drill down to a certain distance to the bottom of the well (a single root). The pump should be turned on and the turntable should be slowly lowered. It is strictly forbidden to go down to the bottom to open the pump.

(1) The new drill bit should be run-in lightly for about half an hour, and then gradually increase to the specified WOB, and it is strictly forbidden to pressurize to start the turntable;

(2) Concentrate and deliver the drill evenly when operating the brake lever to prevent accidents of slipping and sudden drills;

(3) During roller tricone bit drilling, the changes in lithology and the working conditions of the bit should be analyzed at any time according to the change of the drill pair and the operation of the bit, and the drilling parameters should be adjusted in time.

(1) Determine according to the wear of the bearing and teeth, the phenomenon of bearing damage:

The turntable has periodic jumps. If the bit pressure is small, the jump is light. If the bit pressure is big, the jump is heavy; the drilling speed drops; the pump pressure is normal but the pointer of the weight indicator swings.

(2) The phenomenon of cone jamming:

The load on the turntable increases; the turntable chain jumps; the kelly rod is crappy; the turntable is stopped and the car is reversed; the drilling speed drops; the weight indicator pointer swings severely.

(3) The phenomenon of tooth grinding (stripping):

The load of the turntable is reduced; the kelly does not jump; the drilling speed is significantly reduced or there is no footage; the weight indicator indicates smooth and no swing; the pump pressure is normal.

Focus on drilling bits for 20 years.

Among all the oil drill bit manufacturersin China, GREAT Brand is famous for its specialty and service quality.

Excellent Feedback from customers: More than 20 Engineers & 100 senior technical & 50 sales and services team.

Other supplier products

	PDC cutters used for PDC bit, PDC hole opener, PDC reamer	Overview of PDC Cutter PDC cutters are made of diamond micro-powder and cemented carbide substrate sintered under ultra-high pressure and high tem...
	Three Cone Drill Bit For Soft Formation for water well drilling	Overview of Steel Tooth Bit This superior method provides a stronger, more impact-resistant tooth than milling because the metal particle structur...
	Rock Reamer	Professional manufacture to Rock Reamers Overview of Rock Reamer Hole Opener The Rock reamer produced by GREAT company is used to expand the ...
	PDC cutters used for PDC bit, PDC hole opener, PDC reamer	Overview of PDC Cutter PDC cuttersare made of diamond micro-powder and cemented carbide substrate sintered under ultra-high pressure and high te...
	PDC Bit	PDC Bit PDC bit is Polycrystalline Diamond Compact bit ,it also named Diamond bit. pdc bit classification According to the Material Classification...

供应产品

Same products

	Wax injection	卖方: Yihui casting Technology Co., Ltd.	Wax injection This category mainly includes the MAXWAX brand wax injection machinesdeveloped and...
	Moulding tools	卖方: Yihui casting Technology Co., Ltd.	Moulding tools Casting supplies a complete range of jewellery moulding tools designed for profes...
	Moulding machines	卖方: Yihui casting Technology Co., Ltd.	Moulding machines YihuiCasting provides advanced mold making equipments for jewelry designed for...
	3D printer	卖方: Yihui casting Technology Co., Ltd.	3D printer YihuiCasting provides advanced 3d jewelry printers designed for modern jewelry produc...
	3D Design	卖方: Yihui casting Technology Co., Ltd.	3D Design This category includes all 3D printers and relevant spare parts like release films, re...