KK02 Scratch tester
Product Introduction:
With the continuous expansion of the use of plastic molding products, from the point of view of the surface appearance of molded products (creativity)， improving scratch resistance (scratch characteristics) has become an important topic. And scratch resistance is also very important from the point of view that scars formed on the surface of the molded product may reduce the strength of the product. Scratch testing is performed by horizontal movement of the scratch needle against the pattern. Scratch characteristics were previously evaluated by a "constant vertical load test", but the American Society for Materials and Testing (ASTM) and the International Organization for Standardization (ISO) standardized the "vertical load test" (ASTM D7027-05/S019252)。
Scope of application:
The tester uses a steel needle to scratch films, plastics, automotive interior and exterior decorative materials, coating materials, etc., to evaluate the material's "scratch resistance" (scratch characteristics)。
Features of scratch tester:
1. Teaching function
Use this function to set the load zone with high precision before sampling.
2. Easy to operate with touch screen
All functions can be used and configured through the touch screen installed in front of the Settings.
3. the surface has a bump can also test scratches
The Yaru drive for vertical loads uses a county frame mechanism, so that even the surface with a concave and convex pattern can be tested without affecting the linear increase in load characteristics.
4. Memorizable test conditions
Storage capacity up to 20. capable of memorizing test conditions.
Technical parameters:
The KK-02 is fully compliant with I50 and ASTM International standards
Size :W545*D455*H680(mm)
Weight: About 65KG
Test mode: Load increase mode
Speed range :1——200 mm/sec
Vertical (z) load control range :1——50N
Horizontal (x) load test range :50N
在线联系供应商
Other supplier products
 |
Fabric Fiber Shedding Degree Tester (Friction Method)/ | Instrument Testing Principle Lay the specimen flat and fix it on the holder. Make the wet abrasive attached to the friction head perform reciproca... |
 |
Minimum Ignition Energy (MIE) – Dust Cloud Tester/ IEC 61241-2-3 Dust Ignition Tester/ MITC Dust Explosion Tester | Description： Dust Cloud Minimum Ignition Energy Tester disperses a certain mass of dust specimen to be tested into the Hartmann tube device thro... |
 |
The resistance tester for protective clothing materials against metal molten liq/ | Standards: BS EN 348:1992 Protective clothing. Heat-resistant and fire-resistant. Determination of heat transfer in proximity to fire. ISO 9185 - ... |
 |
Hydraulic Oil Filtration and Dewatering Tester | Applications: Hydraulic and lubrication system oil purification and filtration; Hydraulic and lubrication system oil degassing; Hydraulic and lu... |
 |
Micro Controll Constant-Speed Friction Plate Tester | Main uses 1. microcomputer control fixed-speed friction tester is mainly used to measure the friction coefficient and wear rate of automobile brak... |
Same products
 |
Scott Flex Tester | 卖方: 标准集团 | Product Introduction: Scott kneading tester is suitable for back and forth kneading resistance o... |
 |
NEU nanofiber electrospinning device | 卖方: 标准集团 | Content The Nanofiber Electrospinning Unit uses electrospinning techniques to safely and easil... |
 |
KK03 Scratch tester | 卖方: 标准集团 | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
|
|
KK02 Scratch tester | 卖方: 标准集团 | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
 |
KK01 Scratch tester | 卖方: 标准集团 | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
