F605-Epoxy Primer

1、F605-Epoxy Primer

Automotive Paints Supplier

Product Name/Model:F605-Epoxy Primer

Characteristic: Good fillibility, easy sanding, give excellent rust proofing for bare metal,

goodadhesion power to steel, aluminium, galvanized steel and stainless steel, excellent chemicalcorrosion resistance and rust resistance.


Dried and sanded existing finishes, steel, aluminium, stainless steel, galvanizedsteel, glass fiber reinforced plastic.


Wash by warm soap, remove wax, silicon and other contaminations withdegreaser, sandingwith P800-P1000, wash with clean water then keep dry;again with degreaser.

Mixing Ratio

F605 Epoxy Primer

MSH105 EpoxyHardener






F605 Epoxy Primer

MSH105 EpoxyHardener

MSD-63 EpoxyThinner


16-19s to drop off, in 4# viscosity cupat 25°C,


At 20°C, 3 hours with hardener.


Sanded with P600orP800 sand paper, do following construction after drying

Spray GunSet Up

Gravity Feed: 1.2-1.5mm 4-5kg/cm 2Suction Feed: 1.4-1.6mm 4-5kg/cm 2


Coats&Thickness: 2-3 coats, total 25-35um.Flash-Off Time: At 25°C, 5-10minutes between two coats, it depends ontemperature and paint film.

Drying Time

  1. cool down.B. Air-drying time 3 hours, at 20°C.

Shelf Life

2 years in original sealed can, cool and dry place at 25℃.



Note:1. The substrate must be cleaned and sanded before spray, wet sanding P800-1000 and then dry.2. At ambient temperature higher than 30℃, add appropriate Retarder Solvent into thinner toavoid blushing. For more details, please refer to technical data sheet of Retarder Solvent.3. The products mixed with hardener should be used up soon and can not be restore for future use;clean equipments immediately with thinner after application, otherwise it is very difficult to becleaned after dry.


至: Guangzhou Zhenroumei Chemical Coatings Limited
Your E-mail:

Send to other suppliers

Other supplier products

MF600-Plastic Primer
MF600-Plastic Primer 3、MF600-Plastic Primer Automotive Paint company Product Name/Model:MF600-Plastic Primer Characteristic: Single-component transparent fast dryi...
DG2K-Solid Colors
DG2K-Solid Colors DG2K-Solid Colors Auto Refinish Paint Product Name/Model:DG2K-Solid Colors Characteristic:DG2K Solid Colors, high gloss and build, good performa...
MSD-0910 Degreaser
MSD-0910 Degreaser MSD-0910 Degreaser Automotive Refinish Coatings Product Name/Model:MSD-0910 Degreaser Characteristic: Able to remove greaser, oil and other su...
MSD-0960 Thinner SRA
MSD-0960 Thinner SRA MSD-0960 Thinner SRA Automotive Coatings Manufacturer Product Name/Model:MSD-0960 Thinner SRA Characteristic: An additive helps to achieve an invi...
BYTF606-2K Primer Surfacer
BYTF606-2K Primer Surfacer Auto Coatings Product Name/Model:BYTF606-2K Primer Surfacer Characteristic: Multi-purpose two-component 2K Primer Surfacer with strong filling pow...

Same products

PDC (Polycrystalline Diamond Compact) Cutter
PDC (Polycrystalline Diamond Compact) Cutter 卖方: Henan E-Grind Abrasives Co., Ltd. Polycrystalline diamond composite(PDC) E-Polycrystalline diamond composite(PDC) sheet is made of ...
Products 卖方: Henan E-Grind Abrasives Co., Ltd. E-Grind offers a full range of superabrasive, diamonds and CBN powders, as well as a variety of s...
PCD & PCBN 卖方: Henan E-Grind Abrasives Co., Ltd. PCD blanks for Cutting Tools E-Grind supplies the whole range of PCD blanks for cutting tool purp...
Metal Bond Micron Diamond
Metal Bond Micron Diamond 卖方: Henan E-Grind Abrasives Co., Ltd. Metal Bond Micron Diamond E-Grind's metal bond micron products offer good Roughing, Lapping and ...
Metal Bond Mesh Diamond
Metal Bond Mesh Diamond 卖方: Henan E-Grind Abrasives Co., Ltd. E-Grind's metal bond mesh diamondcombines both using life and working efficiency.Suitable for res...