API610 BB4 multistage high pressure pump/BFP pump
API610 BB4 multistage high pressure pump/BFP pump
API 610 Standard Pump
Design:
All parts and components of the SBD series pumps are designed as interchangeable standard parts, which greatly helps to reduce the storage of spare parts.
Intermediate Casing
O-rings are designed between intermediate casings when connecting the sections with tie-bolts. Metal gaskets may also be used to replace the O-rings in case of necessity.
Suction and discharge casings are normally supported with feet construction. However, center supports are used for SBD150, as well as SBD80 and SBD100 when Temp. of pumped media exceeds 150℃.
Hydraulic Model and Balancing of Axial Force
Two different hydraulic models (Impellers and diffusers) are designed for each specification and model to expand the operating range with high efficiency. Replaceable wear rings are adopted for sealing between impeller and casing.
Most of the axial forces shall be balanced by hydraulic balancing device (drum) and the residual force shall be borne by thrust t bearings.
All SBD pumps are oil lubricated, except SBD25 which is lubricated with grease.
Performance Data:
Capacity: Up to 500m3/hr
Head: Up to 1200m
Operating Press.: Up to 15MPa
Operating Temp.: -80 ~ +180℃
Applications：
Water supply,Thermal power plant feed water pump/cooling water pump,Pipeling pressure boosting,Refrigeration project
Flanges
Discharge flanges and suction flanges of center supported pumps are designed as Vertical up, while suction flanges for foot supported pumps can be arranged in any direction.
Shaft Sealing
In general, balanced type Mechanical seals shall be used for shaft sealing. Soft packing is also applicable if necessary.
Shaft seal shall only bear as much as the suction pressure because discharge pressure shall be reduce after passing through the balancing drum.
Packing gland shall be cooled in case the temperature of flushing liquid is higher than 110℃. And the whole packing box shall be cooled if the temperature of flushing liquid is higher than 130℃
Driving End & Rotation
Driving end of the pump is designed at the suction side and CW rotation shall be viewed from the driving end.
在线联系供应商
Other supplier products
 |
vertical centrifugal pipeline pump | API610 OH3 single stage, single suction, radi ally split, vertical centrifugal pipeline pump API 610 Standard Pump API610 VS3 vertical single cen... |
 |
TNH Heavy Duty Slurry Pump，Silicon nitride ceramics | TNH Heavy Duty Slurry Pump，Silicon nitride ceramics Overview TNH/TFN series pumps are horizontal cantilevercentrifugal pump. The material of TNH... |
 |
API610 BB1 single-stage double suction split case centrifugal pump | API610 BB1 single-stage double suction split case centrifugal pump API 610 Standard Pump single-stage centrifugal pump SBM Series pumps, are... |
 |
TDT Desulphurization Pump/FGD Pump | TDT Desulphurization Pump/FGD Pump Slurry Pump TDT Desulphurization Pump manufacturer,50B-L slurry pump TDT、TDTL(R)series FGD pump is single s... |
 |
API610 BB5 multi-stage centrifugal pump | API610 BB5 multi-stage centrifugal pump API 610 Standard Pump multi-stage centrifugal pump General: Type SBT, multi-stage horizontal radial spl... |
Same products
 |
Cover Plate Liner | 卖方: Hebei TIIEC Machinery Co., Ltd | Cover Plate Liner (Polyurethane Material) is a critical wear part of slurry pumps, installed on t... |
 |
metal impeller | 卖方: Hebei TIIEC Machinery Co., Ltd | High-Performance Impellers for Reliable and Efficient Pumps 1. Function & Material Advantage... |
 |
liebherr hydraulic pump | 卖方: Baoding Dingsen Hydraulic Equipment Sales Co., LTD | liebherr hydraulic pump for construction machinery are a critical part of reliable, high-per... |
 |
Heawy Duty Cantilever Sump Pump -VC(R)/VCH/VCS | 卖方: Hebei TIIEC Machinery Co., Ltd | INDUX®Pump Features INDUX®Vertical, single casing structureslurry pumpsare designed for ... |
 |
pump | 卖方: O&K GROUP LIMITED | Looking for Quality Products? From electronics to home essentials, fashion to industrial supplie... |
