Hail Impact Tester for pv module
Standard:According to IEC61215,IEC61646,UL1703 standard requirement
Purpose:to verify that the module is capable of withstanding the impact of hailstones
Technical specifications:
1、launch device
a、Power source is air compressor
b、Air pressure:6-8bar
c、Ice ball single filled by manual
d、The barrel length approx 940mm
e、The barrel can change
2、Moving locating device
a、X shaft move distance approx 2100mm
b、Y shaft move distance approx 1000mm
c、Locating accurate:≤1mm
d、Impact area:2000×1000mm
e、Guide ways is high quality import guide rail
f、Driving ways adopt import servo motor + synchronous wheel
g、Locating control ways is PC control and automatic locating
3、Test velocity system and theory
a、Via determine ice through the infrared test velocity sensor , meanwhile catch by the breaking time T, according to V=S/t calculation ice ball flight velocity
b、Test speed sensor use high accurate infrared test speed sensor
c、Infrared test speed sensor accurate±5％
d、Speed catch range 0～50 m/s
e、Ice ball speed: diameter 25mm, ice ball speed 23.0m/s ±5％
diameter 35mm , ice ball speed 27.2m/s ±5％
diameter 45mm , ice ball speed 30.7m/s ±5％
4、ice make ways and mould
a、take the ice mould filled water and placed in the refrigerator freezing chamber, waiting for the water cooling after, take the mould separate take out ice ball , placed in the ice ball Storage chamber cold storage spare
b、Mould use special material that does not expand easily
c、Inner cavity diameter 25mm＜1％；35mm＜1％；45mm＜1％
d、One mould have 6 ice balls , one specification at least have 2 sets of mould
e、Mould ineer cavity process technical use high accurate CNC machine processing
f、ice ball diameter 25mm＜5％；35mm＜5％；45mm＜5％
g、ice ball weight:7.53g＜5％；20.7g＜5％；43.9g＜5％
h、Refrigerator -10℃
在线联系供应商
Other supplier products
 |
Cord Anchorage pull testing Machine with IEC61215-2:2016 standard | Standard:according to IEC61215-2 standard requirement Purpose:Simulate module during the installation process , The module cord anchorages are uni... |
 |
Thermal cycle/humidity freeze environment chamber | Standard:According to IEC61215,UL1703 standard requirement Purpose: To determine the ability of the module to withstand thermal mismatch, fatigue ... |
 |
UV preconditioning testing chamber for pv module | Standard:According to IEC61215, IEC61646 standard requirement Purpose:to precondition the module with ultra-violet (UV) radiation before the therm... |
 |
Mechanical Load Tester for pv module | Purpose: This test is to determine the ability of the module to withstand wind , snow , static or ice loads Technical specifications: 1、The mach... |
|
|
Hail Impact Tester for pv module | Standard:According to IEC61215,IEC61646,UL1703 standard requirement Purpose:to verify that the module is capable of withstanding the impact of hai... |
Same products
 |
Air Permeability Tester STD- F8 | 卖方: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | 卖方: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | 卖方: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | 卖方: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | 卖方: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
