UV preconditioning testing chamber for pv module

Standard:According to IEC61215, IEC61646 standard requirement

Purpose:to precondition the module with ultra-violet (UV) radiation before the thermal cycle/humidity freeze tests to identify those materials and adhesive bonds that are susceptible to UV degradation

Technical specifications:

1、Use material:can completely obstruct ultraviolet rays,tightness,good thermal insulation’s high quality materials

2、Machine UV total irradiation area:more than 2000mm×2000mm,meanwhile satisfy 2 pcs module (2m×1m)

3、Light source life :system use Xenon lamp single lamp life is 1000 hours , delivery offer one set of spare part, use the life at above 2000 hours

4、Single lamp UVA and UVA relative energy rate:UVB approx occupy total energy 3%~10%

5、Irradiation strength:wavelength 280nm~385nm’s irradiation strength can reach about 100W/m²,280nm～320nm ≦10％,promise the test cycle reduce as far as possible

6、Irradiance uniformity:be better than ±15％

7、Real-time monitor and show UVA and UVB strength

8、UVA (320nm~385nm), UVB(280~320nm) Each one of the fiber optic probes

9、Module surface temperature:60℃±5℃

10、Temperature resolution:0.1℃

11、Ozone: almost no ozone is produced

12、Light ways :upper light, module test plane vertical light source

13、Touch screen operate and real-time monitor , when reached the set value will automatic cut off the light source

14、Real-time figure show module surface temperature, measurement accurate±0.1℃

Other supplier products

	UV preconditioning testing chamber for pv module	Standard:According to IEC61215, IEC61646 standard requirement Purpose:to precondition the module with ultra-violet (UV) radiation before the therm...
	Cord Anchorage pull testing Machine with IEC61215-2:2016 standard	Standard:according to IEC61215-2 standard requirement Purpose:Simulate module during the installation process , The module cord anchorages are uni...
	Thermal cycle/humidity freeze environment chamber	Standard:According to IEC61215,UL1703 standard requirement Purpose: To determine the ability of the module to withstand thermal mismatch, fatigue ...
	Mechanical Load Tester for pv module	Purpose: This test is to determine the ability of the module to withstand wind , snow , static or ice loads Technical specifications: 1、The mach...
	Solar panel Damp heat testing chamber with IEC 61215-2:2016 standard	Standard:According to IEC61215,UL1703 standard requirement Purpose:To determine the ability of the module to withstand the effects of long -term p...

供应产品

Same products

	PH-2398 pH/EC/ORP/温度 多参数测试仪	卖方: 科立龙电子股份有限公司	大显示，可同时进行水质PH、氧化还原电位、电导率、温度的测量； 带背光LCD显示清晰，功能齐全，精度高； 仪表采用微电脑测量与控制技术，具有自动校准功能，方便实用。 内置蓝牙，可以与电脑或...
	ORP-2026S 防水型 土壤ORP&温度 二合一测试仪	卖方: 科立龙电子股份有限公司	范围 ORP -999～999mV Temp 0～50℃ 分辨率 ORP 1mV...
	防水型 EC /TDS/温度三合一参数测试仪	卖方: 科立龙电子股份有限公司	范围 EC ～19.9mS TDS Temp 0～50℃ 分辨率 ...
	EC-98330 电导率营养测试棒	卖方: 科立龙电子股份有限公司	本营养测试仪适用于水培和农业应用，能够准确测量水中的营养液电导率（EC）单位为mS/cm，以及总溶解固体（TDS）转换为百万分之一（ppm）。 适合需要较高EC值的植物，该测试仪具有高达6.0...
	PH-808防水笔式土壤PH计	卖方: 科立龙电子股份有限公司	两点按键校准,自动识别pH标准缓冲液 自动温度补偿确保全量程范围的精确测量。 自动电源关闭，有效节省电池能耗。 可替换型电极降低仪表维护与使用成 全防水性能保障在恶劣环境中对仪表的完整保...