BJ-918B Scrap Cable Wire Stripping Machine

Operation Video ofBJ-918B Scrap Cable Wire Stripping Machine

BJ-918B scrap wire stripper is the most popular multi-function wire stripping equipment at present. The greatest feature of this machine is the upper shaft can be adjusted to work for the minimum diameter of 1.5mm single wire to the maximum diameter up to 100mm rubber cable.

Feature ofBJ-918B Scrap Cable Wire Stripping Machine

• This cable stripping machine is the best choice for small recycler of cable recycling.
• Cut the waste cable into 1-2 meters.
• Put the waste cable into the hole of cable stripper.
• Cable stripped will go out from another side.
• Use hand to separate the copper core and PVC/PE cover
• Get the copper and PVC/PE, and sell to smelters and refiners.
• Should you need cable stripper, cable slitter, cable stripping machine, please contact us today!

Application ofBJ-918B Scrap Cable Wire Stripping Machine

• Diameter from 1.5mm to 98mm
• This machine is widely used in the wire stripping industry. It can peel fiber optics protective covering flat wire, the outsourcing metal steel silk thread, the rubbers electric cable line and high tension cable. It can process 1.5mm diameter monofilament, sheath line and steel wire line and so on. The increased diameter, the upper shaft can be arbitrary up and down.
  
  

Attention ofBJ-918B Scrap Cable Wire Stripping Machine

• The operator should pay special attention to the safety of hands. FATIGUE OPERATION IS FORBIDDEN!
• The pressure should not be too tight. Overload work will shorten the life span of the machine.
• If the cabel cannot get through, operator has to check whether the belt is loose or the pressure is too tight, or the blades are wrong directed.
• If this machine work with heavy duty for a long time, operator has to check the reansmission oil capacity, grease lubrication is required on the fur shaft gears before working every three months.
• Keep daily maintenance of the four bearings, any damage of bearing will cause shaft roken easily after continuous operating.
• When work wth bigger size cables, the upper shaft should be kept hanging on the same line by both sides.
• Any loosing of the four lifting screw nuts of the transmission an dmotor have to be adjusted by fastening the chain and V-belt. Note: the poslition of transmission and the motor have to be kept parallet.

If the copper wire and rubber or plastic cannot be separeated completely, plese pay attenton as below:

• Choose the right feeding hole, adjust the positioning fixture via the diameter of cable.
• Adjust the gap between the drove-gears according to the diameter of cable and the point mentioned in "3" of the following picture. Basically, the gap should be smaller than the diameter or cable.
• Keep both sides of the long blades to be symmetrical, as well as the long blades and the position of fixture.

Other supplier products

	RT-3000 PP Tape Dispenser	Specifications ofRT-3000 PP Tape Dispenser Available Width: 3 ~ 25mm Available Length: 9 ~ 61mm Power Supply: AC110V 60Hz / AC220V 50Hz Mea...
	Pneumatic Terminal Crimping Machine	Pneumatic Terminal Crimping Machine Cable Hydraulic Crimping Machine BJ-30T * Force:20Ton* Applicable Scope:1-200mm² wire* Strok...
	Automatic Spring Separator	The application and maintenance of spring separator: (1) Adjustment of spring external diameter: Mainly when adjusting the spring external diam...
	Automatic Label Rewinder	Automatic Label Rewinder AL-938 Label Rewinder Machine * Available Width: 20 ~ 150mm* Speed: 200mm/sec* Max. OD of Roll: 230mm* ID of R...
	BJ-940 Scrap Copper Wire Stripper Machine	Features of Scrap Copper Wire Stripper Machine BJ-940: This model wire stripping machine is both manually and electrically operated machine.Unde...

供应产品

Same products

	The Ultimate Tool for Bubble-Free Displays	卖方: 深圳市维客修科技有限公司	FORWARD FW-16R除泡机、FW-8R迷你除泡机，在手机、iPhone、iPad、平板屏幕翻新过程中，去除屏幕OCA气泡，最大支持12.9寸屏幕。安全门设计，24V低压风阀配置，有效降低...
	Precision CNC Lathe With Conjoined Oblique Rail Cutter Tower	卖方: Zhejiang Guoyu CNC Machine Tool Co., Ltd.	Technical Characteristics: 45° slant bed base structure, with strict aging treatment, smooth ...
	Rail Welder A Frame aligners railway welding tools	卖方: 834406	产品描述 A型车架 A-Frame 是一种导轨对准器，可精确对准要焊接的导轨。该设备在焊接操作期间将导轨固定到位。
	2 parts fluid mixing dispenser 2 component dosing epoxy PU silicon rubber vacuum system	卖方: 824681	What is the difference between 2K AB adhesive materials manual potting machine and robot pottingm...
	Horizontal Machining Center	卖方: Xilong (Shanghai) Machine Tool Co., Ltd.	Horizontal Machining Center parts can automatically finish four sides milling, boring, drilling, ...