SSAW Spiral Welded Pipe
SSAW spiral welded pipe is a spiral seam steel pipe
welded by automatic double wire
double side submerged arc welding process
SSAW spiral welded pipe is a spiral seam steel pipe welded by automatic double wire and double side submerged arc welding process, which is made of steel strip coils as raw material, extruded at high temperature and welded by automatic double wire and double side submerged arc welding.
SSAW spiral welded pipe includes ordinary spiral steel pipe and thick wall spiral steel pipe. The advantages of thick-walled spiral steel pipe compared with ordinary thick spiral steel pipe are: high compressive strength, high impact strength, high safety performance and longer service life. The strength of SSAW spiral welded pipe is generally higher than that of straight welded pipe. The welded pipe with larger diameter can be produced with narrow blank, and the welded pipe with different diameter of pipe can be produced with the same width of blank. The nominal diameter of SSAW spiral welded pipe is also called average outer diameter. This is due to the thin metal pipe, the outer diameter of the tube and the tube diameter is similar, so take the outer diameter of the tube and the average diameter of the pipe as the diameter of the call.
1.the welding clearance control device is used to ensure that the weld clearance meets the welding requirements, and the pipe diameter, misalignment and weld clearance are strictly controlled.
2 butt joint of strip head and tail, single wire or double wire submerged arc welding, automatic submerged arc welding after rolling steel pipe.
3. the welding seam is inspected by the continuous ultrasonic automatic wound tester on line, which ensures the nondestructive testing coverage of the helical weld. If there are defects, automatic alarm and spray marking, the production workers at any time to adjust the process parameters, timely eliminate defects.
4.Before forming, the strip is straightened, trimmed, planed, surface cleaned, transported and precurved.
5.The electric contact pressure gauge is used to control the pressure of the oil cylinder on both sides of the conveyer to ensure the smooth conveyance of strip steel.
6.after cutting into a single steel pipe, every batch of steel pipe shall carry out strict first inspection system to check the mechanical properties, chemical composition, melting condition, surface quality of steel tube and non-destructive inspection to ensure that the pipe making process is qualified. Can be formally put into production.
7.Weld seam with continuous sound wave flaw detection mark, after manual ultrasonic and X-ray review, if there is a defect, after repair, again after non-destructive testing, until the defect has been eliminated.
If you require further information or you do not see what yo need in our web,please do not hesitate to contact us. Our customer service specialists will be happy to help you.
Other supplier products
|
|
Concentric Reducer Pipe Fittings |
Product specification: 3 / 4 "X 1 / 2" -48 "X 40" [DN 20 X 15-1200 X 1000]
Wall thickness size: Sch. 5s 160
Standard: GB/T12459-2005, (ANIS),... |
|
|
Rectangular Low Carbon Steel Pipe |
Grade :A53(A,B), A369, St37, St52, St42, ST35, Q235, Q345, Q195 Length :2-12meter Outer Diameter :20-400mm Thickness :0.8-13mm...
rectangular low ... |
|
|
Monel Steel |
Monel Steel
bar （mm）8-300MM
Wire (mm) 0.2-8MM
Outer diameter of steel tube (mm) 3-426MM0.5-60 wall thickness
Strip (mm) thickness 0.05-... |
|
|
ASTM A210 Seamless Carbon Super Heater Tubes |
ASTM A210 Seamless Carbon Super Heater Tubes
Grade :A210A1、A210C
OD:12.7 to 127 mm
WT:0.9 to 12.7 mm
ASTM A210 is the standard covers... |
|
|
90°Elbows Pipe Fittings 45° Elbows Pipe Fittings |
90°Elbows Pipe Fittings
A 90°elbow is a metal pipe fitting that changes the direction of the pipe on a carbon steel pipe. Connection mode ... |
供应产品
Same products
