Sling Ejector Pin JHN03
Ejector pinis the “bouncer” of the injection molding world. They apply force to eject a part from the mold, and in some cases can leave marks. We are to design and position pins to minimize their effect on your parts. You can apply this product to release elasticity from the bottom. And the features of the product are that it can adjust to the required eject height in advance and it is easy to install.
Material Hardness
1.2101 HRC58°±2
Product Details
Type Dimension
AB C D H
JHN03-1 6 M10x0.75 16 3x87
JHN03-2 8 M12x0.75 18 4x109
JHN03-3 10 M14X0.75 20 4x1211
JHN03-4 12 M16x0.75 22 4x1413
Because the contact surface is parallel with the ejector plate, the thickness of release elasticity from the bottom's smallest area is just 4mm, and a new characteristic of this product is that ejecting first and then releases elasticity from the bottom.
在线联系供应商
Other supplier products
 |
Embedded Spring | Characteristic description of embedded spring:Hard screws are fixed directly inside the alloyThe stainless steel screw is directly fixed inside t... |
 |
Positioning Components-Locking Block Sets | Material Hardness 1.2343 HRC50°~56° Type Dimension t d4 d I5 I4 I3 I2 I1 S1 b3 JHN09/30 5 4... |
 |
MateriaSpure Bushing-A Type JH025 | Inner HardnessSurface HardnessHeat Treatment S45CSR section HRC50°~55°Partial HRC60°±2°HRC60°±2°Vacuumed SKD1... |
 |
CP-CPS-CPH-CPHS Gas Spring-Higher Forces | CP-CPS-CPH-CPHS Higher Forces Nitrogen Gas Spring series: • Higher forces in the same diameter. • Higher loading pressure. • Conn... |
 |
Shoulder Ejector Sleeve Pins | Material InnerHardness SurfaceHardness Heat Treatment FDAC HRC38°±2° HV1000°±100° Nitrided HRC5... |
Same products
 |
折弯机模具 | 卖方: 河北儒涵商贸有限公司 | 折弯机模具分为折弯机上模和折弯机下模，它是折弯机的重要组成部分，它利用折弯机的压力将工件加工成我们想要的立体图形 |
|
|
Sling Ejector Pin JHN03 | 卖方: TAIZHOU HUANGYAN JINHONG MOULD PARTS CO.,LTD. | Ejector pinis the “bouncer” of the injection molding world. They apply force to eject... |
 |
Design, process and manufacture blow mold and injection mold | 卖方: 广州市鸿英包装制品有限公司 | The mold can be customized according to the design drawing or the material object，We have 25 year... |
 |
电熔管件接线柱 | 卖方: 成都派斯克机械有限公司 | 专业和经验丰富的设计团队 ： 电熔管件有它特殊的性质，它不仅是一个塑料产品，功能是通过植入在管件内壁的发热丝两端，施加一定的电流、电压，通过发热融化塑料起到连接的作用。电熔管件的设计需考虑：产品... |
 |
电熔管帽注塑模具 | 卖方: 成都派斯克机械有限公司 | 专业和经验丰富的设计团队 ： 电熔管件有它特殊的性质，它不仅是一个塑料产品，功能是通过植入在管件内壁的发热丝两端，施加一定的电流、电压，通过发热融化塑料起到连接的作用。电熔管件的设计需考虑：产品... |
